Bedienungsanleitung Bosch GPB 18V-2 C (Seite 18 von 259) (Alle Sprachen)

786237

Zoom out

Zoom in

Vorherige Seite

1/259

Nächste Seite

18 | English

Setting/Saving FM Radio Stations

To select the audio source FM radio stations, press the

source button(7) untilFM orFM2 appears on the audio

source indicator(b).

GPB18V‑2C: The frequency of the current station will ap-

pear on the radio frequency indicator(d).

GPB18V-2SC: The frequency of each current station will

appear on the top line of the multi-function indicator(k). The

additional information shown on the bottom line of the multi-

function indicator can be set with the menu function.

If there is sufficiently good reception of a suitable signal, the

radio will automatically switch to stereo reception, and the

stereo indicator(h) will appear in the display. The reception

type can be changed to mono reception with the menu func-

tion.

– To set a specific station, turn the source button(7)

(TUNE) until the required frequency or the required sta-

tion is shown in the display.

– To search for the next station with high signal

strength, briefly press the seek button (scan down)(10)

or the seek button (scan up)(9). The next station found is

shown in the display and played back.

– To search for all stations with high signal strength,

press the seek button (scan down)(10) or the seek but-

ton (scan up)(9) for longer than half a second. Any sta-

tion found is played back for 5 seconds, then the search

is continued until the end of the frequency band. To can-

cel the station search, briefly press the seek button (scan

down)(10) or the seek button (scan up)(9).

– To save a set station, press the preset button(5) of the

required storage space until the number of the storage

space appears in the storage space indicator(c).

If the four storage spaces of theFM audio source are oc-

cupied, then switch to theFM2 audio source, in which

four further storage spaces are available, by pressing the

source button(7). Please note that you must reset the re-

quired station after switching to save the change.

– To automatically search for and save the stations with

the best reception (AUTOSTORE), press the seek button

(scan down)(10) and the seek button (scan up)(9) sim-

ultaneously. The radio will check all receivable stations

and save the four stations with the best reception in pre-

set spaces 1 to 4. Please note that stations that have

already been saved will be overwritten here where neces-

sary.

Once the search has finished, the station saved in preset

space 1 will be played back.

– To start playback of a saved station, briefly press one of

the preset buttons(5). The number of the storage space

will appear on the storage space indicator(c). If required,

switch between audio sourcesFM andFM2 by pressing

the source button(7), to allow you to go back to all saved

stations.

Setting the Rod Antenna

The radio is supplied with a fitted rod antenna(6). For FM

radio operation, point the rod antenna in the direction that

enables the best reception.

If the reception is insufficient, position the radio at a differ-

ent location that enables better reception.

Note: When operating the radio in the direct vicinity of ra-

dio-communication equipment or radio transceivers, or

other electronic equipment, the radio reception can be sub-

ject to interference.

Connecting External Audio Sources via AUX

Remove the protective cap of the connector

compartment(15) and insert the 3.5‑mm connector of the

AUX cable(25) into the AUXIN socket(24). Connect the

AUX cable to a suitable audio source.

To play back the AUX audio source, press the source

button(7) untilAUX appears on the audio source

indicator(b).

After removing the AUX cable connector, reattach the pro-

tective cap of the connector compartment(15) to protect

against dirt/debris.

If one of the preset buttons(5) is pressed during AUX opera-

tion, the radio will switch to the station that was saved in the

last used radio operating mode.

Playing Back/Controlling External Audio Sources via

Bluetooth®

To play back an audio source (e.g. smartphone) via

Bluetooth®, either press the source button(7) until the

Bluetooth® indicator(a) appears in the display, or briefly

press the Bluetooth® button(11) regardless of the current

audio source.

Whilst a connection is being established or during the search

for a connection, theBluetooth®indicator(a) will flash.

GPB18V‑2SC:<Pairing> will appear on the multi-function

indicator(k).

– If the radio has already been connected to an external au-

dio source via Bluetooth® and if this audio source is avail-

able, a connection to this audio source will automatically

be established.

– If no saved audio sources are available, the search pro-

cess will start. Activate the new connection via the ex-

ternal audio source. For smartphones, that is generally

possible via the settings in the Bluetooth® menu. The ra-

dio will appear as an available source under the name

GPB18V‑2C xxxx or GPB18V‑2SC xxxx. Please ob-

serve the operating instructions for your audio source/

smartphone.

– If an available connection to an audio source via

Bluetooth® needs to be ended and a new connection

needs to be searched for (PAIRING), press the

Bluetooth® button(11) for longer than 0.5seconds. Ac-

tivate the connection as described above.

As soon as an audio source is connected via Bluetooth®, the

Bluetooth® indicator(a) will light up continuously.

GPB18V‑2SC: The name of the device connected via

Bluetooth® is displayed on the top line of the multi-function

1 609 92A 7XU | (27.05.2022) Bosch Power Tools

Bosch GPB 18V-2 C Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info