Bedienungsanleitung Bosch GRW 18-2 E Professional (Seite 12 von 153) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

594777

Zoom out

Zoom in

Vorherige Seite

1/153

Nächste Seite

12 | English

1 609 92A 0HJ | (4.11.13) Bosch Power Tools

across flats 24 mm), and use a second open-ended spanner

(width across flats 22 mm or 24 mm) to tighten the stirrer

paddle 5.

The stirrer paddle is disassembled in reverse order.

Operation

Starting Operation

 Observe the mains voltage! The voltage of the power

source must correspond with the data on the type plate

of the machine.

 Dusts, e. g. mineral dusts, can be harmful to one’s health.

Contact with or inhaling the dusts can trigger allergic reac-

tions to the operator or bystanders and/or lead to respira-

tory infections.

Materials containing asbestos may only be worked on by

specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

Gear selection, mechanical (GRW 18-2 E)

 Operate the gear selector 1 only when the power tool is

not in use.

Press in the gear selector 1 and slide it until it locks.

Two speed ranges can be preselected with the gear selector

Gear I:

Low speed range; for working up to a stirrer paddle di-

ameter of 180 mm.

Gear II:

High speed range; for working up to a stirrer paddle di-

ameter of 140 mm.

If the gear selector 1 cannot be slid all the way at standstill,

turn the drive spindle slightly with the stirrer paddle.

Switching On and Off

To start the machine, press the On/Off switch 2 and keep it

pressed.

Press the lock-on button 3 to lock the

pressed on/off switch 2.

To switch off the machine, release the On/Off switch 2 or

when it is locked with the lock-on button 3, briefly press the

On/Off switch 2 and then release it.

To save energy, only switch the power tool on when using it.

Adjusting the Speed

The speed of the switched on power tool can be variably ad-

justed, depending on how far the On/Off switch 2 is pressed.

Light pressure on the On/Off switch 2 results in a low rotation-

al speed. Further pressure on the switch results in an increase

in speed.

Working Advice

 Do not use the power tool in a stand.

 Avoid splashing around the material being stirred. Oth-

erwise, you could slip and lose control over the power tool.

 Avoid continuous operation of the power tool at re-

duced speed. Otherwise the motor of the power tool could

overheat.

To release the lock-on button 3, briefly press the on/off

switch 2 and then let it go. This will prevent the power tool

from restarting unintentionally (risk of injury).

Selection of the stirrer paddle is dependent on the material

that is to be stirred.

For materials with low viscosity, e.g. emulsion paint, varnish-

es, adhesive, grouting compound, cement slurry, use a stirrer

paddle with a left-hand spiral. The material is moved from the

top downwards in a stirrer paddle with a left-hand spiral. The

stirrer paddle is pushed upwards. Materials with low viscosity

are mixed in a way which minimises splattering.

For materials with high viscosity, e.g. plaster, concrete, ce-

ment, screed, filler, epoxy resin, use a stirrer paddle with

right-hand spiral. The material is moved from the bottom up-

wards in a stirrer paddle with a right-hand spiral. The stirrer

paddle works its way into the mixture. Materials with high vis-

cosity are mixed thoroughly.

While mixing, move the power tool in an up and down motion.

Clean the stirror paddle after use.

 Store the power tool in a safe place. Ensure that it can-

not fall over. Otherwise, the machine may become dam-

aged.

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine itself, pull the mains

plug.

 For safe and proper working, always keep the machine

and ventilation slots clean.

If the replacement of the supply cord is necessary, this has to

be done by Bosch or an authorized Bosch service agent in or-

der to avoid a safety hazard.

OBJ_BUCH-1972-003.book Page 12 Monday, November 4, 2013 2:14 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GRW 18-2 E Professional Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info