Bedienungsanleitung Bosch GSA 18 V-LI Professional (Seite 15 von 198) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

594588

Zoom out

Zoom in

Vorherige Seite

1/198

Nächste Seite

English | 15

Bosch Power Tools 1 609 92A 110 | (16.12.14)

Declaration of Conformity

We declare under our sole responsibility that the product de-

scribed under “Technical Data” is in conformity with all rele-

vant provisions of the directives 2011/65/EU, 2014/30/EU,

2006/42/EC including their amendments and complies with

the following standards: EN 60745-1, EN 60745-2-11.

Technical file (2006/42/EC) at:

Robert Bosch GmbH, PT/ETM9,

70764 Leinfelden-Echterdingen, GERMANY

Robert Bosch GmbH, Power Tools Division

70764 Leinfelden-Echterdingen, GERMANY

Leinfelden, 13.11.2014

Assembly

Battery Charging

 Use only the chargers listed in the technical data. Only

these chargers are matched to the lithium-ion battery of

your power tool.

Note: The battery supplied is partially charged. To ensure full

capacity of the battery, completely charge the battery in the

battery charger before using your power tool for the first time.

The lithium-ion battery can be charged at any time without re-

ducing its service life. Interrupting the charging procedure

does not damage the battery.

The lithium-ion battery is protected against deep discharging

by the “Electronic Cell Protection (ECP)”. When the battery is

empty, the machine is switched off by means of a protective

circuit: The inserted tool no longer rotates.

 Do not continue to press the On/Off switch after the

machine has been automatically switched off. The bat-

tery can be damaged.

Observe the notes for disposal.

Removing the battery

The battery 9 is equipped with two locking levels that should

prevent the battery from falling out when pushing the battery

unlocking button 8 unintentionally. As long as the battery is

inserted in the power tool, it is held in position by means of a

spring.

To remove the battery 9, press the battery unlocking button 8

and pull the battery out of the power tool toward the rear. Do

not exert any force.

Battery Charge-control Indication (see figure A)

The three green LEDs of the battery charge-control indicator

12 indicate the charge condition of the battery 9. For safety

reasons, it is only possible to check the status of the charge

condition when the machine is at a standstill.

Press button 11 to indicate the charge condition. This is also

possible when the battery 9 is removed.

When no LED lights up after pushing button 11, then the bat-

tery is defective and must be replaced.

Replacing/Inserting the Saw Blade

 Before any work on the power tool, remove the battery.

 When mounting the saw blade, wear protective gloves.

Danger of injury when touching the saw blade.

 When changing the saw blade, take care that the saw

blade holder is free of material residue, e. g. wood or

metal shavings.

Selecting a Saw Blade

Use only saw blades suitable for the material being worked.

An overview of recommended saw blades can be found at the

beginning of these instructions. Use only ½" universal shank

saw blades. The saw blade should not be longer than required

for the intended cut.

Use a thin saw blade for narrow curve cuts.

Inserting the Saw Blade (see figure B)

Press the saw blade 1 firmly into the saw blade holder 3 until

it can clearly be heard to engage. This causes the locking

sleeve 4 to turn by approx. 90° and locks the saw blade.

If the saw blade 1 is not locked, turn the locking sleeve 4 ap-

prox. 90° in the direction of the arrow until it locks in the open

position and a “click” can be heard. Then press the saw blade

1 into the saw blade holder 3 again.

 Check the tight seating of the saw blade. A loose saw

blade can fall out and lead to injuries.

For certain work, the saw blade 1 can also be turned through

180° (with the teeth pointed upwards) and re-inserted again.

Ejecting the Saw Blade (see figure C)

 When ejecting the saw blade, hold the machine in such

a manner that no persons or animals can be injured by

the ejected saw blade.

Turn the locking sleeve 4 approx. 90° in the direction of the

arrow. The saw blade 1 is ejected.

Dust/Chip Extraction

 Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Henk Becker

Executive Vice President

Engineering

Helmut Heinzelmann

Head of Product Certification

PT/ETM9

LED Capacity

Continuous lighting 3 x green  2/3

Continuous lighting 2 x green  1/3

Continuous lighting 1 x green <1/3

Flashing light 1 x green Reserve

OBJ_BUCH-760-006.book Page 15 Tuesday, December 16, 2014 4:21 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GSA 18 V-LI Professional Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info