Bedienungsanleitung Bosch GSA 900 E (Seite 19 von 208) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

110212

Zoom out

Zoom in

Vorherige Seite

1/208

Nächste Seite

English | 19

Bosch Power Tools 1 609 929 N64 | (28.1.08)

Working Advice

Tips

f When sawing light building materials, ob-

serve the statutory provisions and the rec-

ommendations of the material suppliers.

Check wood, press boards, building materials,

etc. for foreign objects such as nails, screws or

similar, and remove them, if required.

Switch the machine on and guide it toward the

workpiece. Position the footplate 2 onto the sur-

face of the work and saw through the material

applying uniform contact pressure and feed. Af-

ter completing the working procedure, switch

the machine off.

If the saw blade should jam, switch the machine

off immediately. Widen the gap somewhat with

a suitable tool and pull out the machine.

Plunge Cutting (see figures E–F)

f The plunge cutting procedure is only suita-

ble for treating soft materials such as wood,

plaster board or similar! Do not work metal

materials with the plunge cutting proce-

dure!

Use only short saw blades for plunge cutting.

Place the machine with the edge of the footplate

2 onto the workpiece and switch on. For power

tools with stroke speed control, set the maxi-

mum stroke speed. Press the power tool firmly

against the workpiece and allow the saw blade

to slowly plunge into the workpiece.

As soon as the footplate 2 fully lays on the sur-

face of the workpiece, continue sawing along-

side the desired cutting line.

For certain work, the saw blade 1 can also be in-

serted turned through by 180° and the sabre

saw can be guided accordingly in a reversed

manner.

Flush Cuts (see figure G)

Using elastic bimetal saw blades, items still at-

tached to a wall (e. g. projecting building ele-

ments such as water pipes, etc.) can be sawn off

flush at the wall.

f Pay attention that the saw blade always ex-

tends beyond the diameter of the material

being worked. There is danger of kickback.

Position the saw blade directly against the wall

and apply some lateral pressure via the tool until

the footplate faces against the wall. Switch the

power tool on and saw through the workpiece,

applying constant lateral pressure.

Coolant/Lubricant

When sawing metal, coolant/lubricant should be

applied alongside cutting line because of the

material heating up.

Maintenance and Service

Maintenance and Cleaning

f Before any work on the machine itself, pull

the mains plug.

f For safe and proper working, always keep

the machine and ventilation slots clean.

Clean the saw blade holder preferably with com-

pressed air or a soft brush. Remove the saw

blade from the power tool for this. Ensure prop-

er operation of the saw blade holder by applying

a suitable lubricant.

Heavy contamination of the machine can lead to

malfunctions. Therefore, do not saw materials

that produce a lot of dust from below or over-

head.

If the machine should fail despite the care taken

in manufacturing and testing procedures, repair

should be carried out by an after-sales service

centre for Bosch power tools.

In all correspondence and spare parts order,

please always include the 10-digit article

number given on the type plate of the machine.

OBJ_BUCH-68-003.book Page 19 Monday, January 28, 2008 11:32 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GSA 900 E Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info