Bedienungsanleitung Bosch GSB 10.8V-35 (Seite 12 von 20) (Englisch)

786086

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

12 | English

used, the application tool will be stopped when the screw is

driven flush into the material or once the set torque has been

reached. In position the overload clutch is deactivated,

e.g. for drilling.

When unscrewing screws, you can select a higher setting or

set the tool to the symbol.

Mechanical gear selection

uOnly operate the gear selector (6) when the power

tool is not in use.

You can preselect two speed ranges with the gear selector

(6).

Gear I:

Low speed range; for screwdriving or working with a large

drilling diameter.

Gear II:

High speed range; for working with a small drilling diameter.

Setting the Operating Mode

Drilling

GSR

Set the torque presetting ring (4) to the

"drilling" symbol.

GSB

Set the operating mode presetting ring (5) to

the "drilling" symbol.

Screwdriving

GSR

Set the torque presetting ring (4) to the re-

quired torque.

GSB

Set the operating mode presetting ring (5) to

the "screwdriving" symbol.

Set the torque presetting ring(4) to the re-

quired torque.

Impact drilling (GSB)

Set the operating mode presetting ring (5) to

the "impact drilling" symbol.

Adjusting the Speed/Impact Rate

You can adjust the speed/impact rate of the power tool when

it is on by pressing in the on/off switch (10) to varying ex-

tents.

Applying light pressure to the on/off switch (10) results in a

low rotational speed/impact rate. Applying increasing pres-

sure to the switch increases the speed/impact rate.

Switching on/off

To start the power tool, press and hold the on/off switch

(10).

To switch off the power tool, release the on/off switch (10).

Fully automatic spindle lock (Auto-Lock)

The drill spindle, and therefore the tool holder (1), are

locked when the on/off switch (10) is not pressed.

This enables screws to be screwed in even when the battery

(9) is empty and allows the power tool to be used as a

screwdriver.

Battery charge-control indicator

When the on/off switch (10) is pressed in halfway or com-

pletely, the battery charge-control indicator (11) indicates

the charge condition of the battery for several seconds. The

indicator consists of three green LEDs.

The three LEDs of the battery charge-control indicator (11)

and the lamp (12) flash urgently when the temperature of

the battery falls or rises outside the operating temperature

range of –20 to +50°C.

LED Capacity

Continuous light 3 x green ≥ 76%

Continuous light 2 x green 51–75%

Continuous light 1 x green 26–50%

Slowly flashing light 1 x green ≤ 25%

Temperature-dependent overload protection

In normal conditions of use, the power tool cannot be over-

loaded. If there is an extreme overload, the power tool

switches off until the optimal operating temperature range is

reached again.

This status is indicated by the three battery charge indicator

(11) LEDs flashing in a chase sequence. The LEDs turn off if

the power tool has reached the optimum operating temper-

ature again.

Practical advice

uOnly apply the power tool to the screw/nut when the

tool is switched off. Rotating tool inserts can slip off.

After working at a low speed for an extended period, you

should operate the power tool at the maximum speed for ap-

proximately three minutes without load to cool it down.

When drilling into metal, only use sharpened HSS drills (HSS

= high-speed steel) which are in perfect condition. The

Bosch accessory range guarantees appropriate quality.

Before screwing larger, longer screws into hard materials, it

is advisable to pre-drill a pilot hole with the core diameter of

the thread to approx. 2/3 of the screw length.

Belt clip (see figure E)

You can use the belt clip (16) to hang the power tool on a

belt, for example. You then have both hands free and the

power tool is always within easy reach.

Bit holder (see figure F)

You can place screwdriver bits in the bit holder (17) for stor-

age.

Colour clip (see figure G)

The colour clip (18) can only be used if the belt clip (16) or

bit holder are not fitted.

1 609 92A 6G9 | (17.06.2021) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GSB 10.8V-35 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info