Bedienungsanleitung Bosch GSB 22-2 CE (Seite 21 von 121) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

78822

Zoom out

Zoom in

Vorherige Seite

1/121

Nächste Seite

English | 21

Bosch Power Tools 1 609 929 M29 | (10.9.07)

Assembly

Auxiliary Handle (see figure A)

f Operate your machine only with the auxiliary

handle 10.

The auxiliary handle 10 can be set to any position

for a secure and low-fatigue working posture.

Turn the bottom part of the auxiliary handle 10 in

counterclockwise direction and swivel the auxil-

iary handle 10 to the desired position. Then

retighten the bottom part of the auxiliary handle

10 by turning in clockwise direction.

Adjusting the Drilling Depth (see figure A)

The required drilling depth X can be set with the

depth stop 11.

Press the button for the depth stop adjustment 9

and insert the depth stop into the auxiliary han-

dle 10.

Pull out the depth stop until the distance be-

tween the tip of the drill bit and the tip of the

depth stop correspond with the desired drilling

depth X.

The knurled surface of the depth stop 11 must

face upward.

Changing the Tool

f Before any work on the machine itself, pull

the mains plug.

Keyless Chuck (see figure B)

The drill spindle is locked when the On/Off

switch 6 is not pressed. This makes quick, con-

venient and easy changing of the tool in the drill

chuck possible.

Open the keyless chuck 1 by turning in rotation

direction n, until the tool can be inserted. Insert

the tool.

Firmly tighten the collar of the keyless chuck 1 by

hand in rotation direction o until the locking ac-

tion (“click”) is no longer heard. This automati-

cally locks the chuck.

The locking is released again to remove the tool

when the collar is turned in the opposite direc-

tion.

Key Type Drill Chuck (see figure C)

f Wear protective gloves when changing the

tool. The drill chuck can become very hot dur-

ing longer work periods.

Open the key type drill chuck 13 by turning until

the tool can be inserted. Insert the tool.

Insert the chuck key 12 into the corresponding

holes of the key type drill chuck 13 and clamp the

tool uniformly.

Screwdriver Tools (see figure D)

When working with screwdriver bits 14, a univer-

sal bit holder 15 should always be used. Use only

screwdriver bits that fit the screw head.

For driving screws, always position the “Drill-

ing/Impact Drilling” selector switch 2 to the

“Drilling” symbol.

Replacing the Drill Chuck

f Before any work on the machine itself, pull

the mains plug.

f For power tools without spindle lock, the

drill chuck must be replaced by an author-

ised after-sales service agent for Bosch pow-

er tools.

The drill chuck must be tightened with a

tightening torque of approx. 35–40 Nm.

Operation

Starting Operation

f Observe correct mains voltage! The voltage

of the power source must agree with the

voltage specified on the nameplate of the

machine. Power tools marked with 230 V can

also be operated with 220 V.

Reversing the Rotational Direction

(see figures E–F)

f Actuate the rotational direction switch 7 on-

ly when the machine is at a standstill.

The rotational direction switch 7 is used to re-

verse the rotational direction of the machine.

However, this is not possible with the On/Off

switch 6 actuated.

OBJ_BUCH-486-001.book Page 21 Monday, September 10, 2007 9:49 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GSB 22-2 CE Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info