Bedienungsanleitung Bosch GSB 24-2 (Seite 16 von 277) (Alle Sprachen)

786458

Zoom out

Zoom in

Vorherige Seite

1/277

Nächste Seite

16 | English

uNever service damaged battery packs. Service of bat-

tery packs should only be performed by the manufacturer

or authorized service providers.

Safety Warnings for Drills

Safety instructions for all operations

uWear ear protectors when impact drilling. Exposure to

noise can cause hearing loss.

uUse the auxiliary handle(s). Loss of control can cause

personal injury.

uHold the power tool by insulated gripping surfaces,

when performing an operation where the cutting ac-

cessory or fasteners may contact hidden wiring. Cut-

ting accessory or fasteners contacting a "live" wire may

make exposed metal parts of the power tool "live" and

could give the operator an electric shock.

uHold the power tool by insulated gripping surfaces,

when performing an operation where the cutting ac-

cessory or fasteners may contact hidden wiring or its

own cord. Cutting accessory or fasteners contacting a

"live" wire may make exposed metal parts of the power

tool "live" and could give the operator an electric shock.

Safety instructions when using long drill bits

uNever operate at higher speed than the maximum

speed rating of the drill bit. At higher speeds, the bit is

likely to bend if allowed to rotate freely without contact-

ing the workpiece, resulting in personal injury.

uAlways start drilling at low speed and with the bit tip

in contact with the workpiece. At higher speeds, the bit

is likely to bend if allowed to rotate freely without contact-

ing the workpiece, resulting in personal injury.

uApply pressure only in direct line with the bit and do

not apply excessive pressure.Bits can bend causing

breakage or loss of control, resulting in personal injury.

Additional safety warnings

uSwitch the power tool off immediately if the applica-

tion tool becomes blocked. Be prepared for high

torque reactions which cause kickback. The applica-

tion tool becomes blocked when it becomes jammed in

the workpiece or when the power tool becomes over-

loaded.

uHold the power tool securely. When tightening and

loosening screws be prepared for temporarily high torque

reactions.

uSecure the workpiece. A workpiece clamped with

clamping devices or in a vice is held more secure than by

hand.

uUse suitable detectors to determine if there are hid-

den supply lines or contact the local utility company

for assistance. Contact with electric cables can cause

fire and electric shock. Damaging gas lines can lead to ex-

plosion. Breaking water pipes causes property damage.

uUse suitable detectors to determine if utility lines are

hidden in the work area or call the local utility com-

pany for assistance. Contact with electric lines can lead

to fire and electric shock. Damaging a gas line can lead to

explosion. Penetrating a water line causes property dam-

age or may cause an electric shock.

uAlways wait until the power tool has come to a com-

plete stop before placing it down. The application tool

can jam and cause you to lose control of the power tool.

uIn case of damage and improper use of the battery, va-

pours may be emitted. The battery can set alight or ex-

plode. Ensure the area is well ventilated and seek medical

attention should you experience any adverse effects. The

vapours may irritate the respiratory system.

uDo not open the battery. There is a risk of short-circuit-

ing.

uThe battery can be damaged by pointed objects such

as nails or screwdrivers or by force applied externally.

An internal short circuit may occur, causing the battery to

burn, smoke, explode or overheat.

uOnly use the battery with products from the manufac-

turer. This is the only way in which you can protect the

battery against dangerous overload.

Protect the power tool against heat, e.g.

against continuous intense sunlight, fire,

water, and moisture. There is a risk of explo-

sion.

Protect the battery against heat, e.g. against

continuous intense sunlight, fire, dirt, water

and moisture. There is a risk of explosion and

short-circuiting.

uConnect the power tool to a mains supply that is prop-

erly connected to earth. The socket and extension cable

must have a fully functioning protective conductor.

Products sold in GB only:

Your product is fitted with an BS 1363/A approved electric

plug with internal fuse (ASTA approved to BS 1362).

If the plug is not suitable for your socket outlets, it should be

cut off and an appropriate plug fitted in its place by an au-

thorised customer service agent. The replacement plug

should have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible

shock hazard and should never be inserted into a mains

socket elsewhere.

Product Description and

Specifications

Read all the safety and general instructions.

Failure to observe the safety and general in-

structions may result in electric shock, fire

and/or serious injury.

Please observe the illustrations at the beginning of this oper-

ating manual.

Read all the safety and

general instructions. Fail-

ure to observe the safety

and general instructions

1 609 92A 7YU | (01.06.2022) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GSB 24-2 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info