Bedienungsanleitung Bosch gsb 24 ve-2 (Seite 36 von 46) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

386390

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

English

21. The saw blades body must be thinner than the

riving knife and the width of cut, or kerf (with

teeth set) must be greater than the thickness of

the riving knife.

22. Never operate the circular saw with the saw blade

turned upward or the side.

23. Ensure that the material is free of foreign matters

such as nails.

24. The riving knife should always be used except

when plunging in the middle of the workpiece.

25. The saw blades range should be from 165 mm

to 150 mm.

26. Be careful of brake kickback.

This circular saw features an electric brake that

functions when the switch is released. As there

is some kickback when the brake functions, be

sure to hold the main body securely.

27. Avoid cutting in the state where the base has

floated up from the material.

When blade is binding, or when interrupting a cut

for any reason, release the trigger and hold the

saw motionless in the material until the blade

comes to a complete stop. Never attempt to

remove the saw from the work or pull the saw

backward while the blade is in motion or KICKBACK

may occur. Investigate and take corrective actions

to eliminate the cause of blade binding.

28. Support large panels to minimize the risk of blade

pinching and KICKBACK. Large panels tend to sag

under their own weight. Supports must be placed

under the panel on both sides, near the line of

cut and near the edge of the panel as shown in

Fig. 1.

To minimize the risk of blade pinching and kickback.

When cutting operation requires the resting of the

saw on the work piece, the saw shall be rested

on the larger portion and the smaller piece cut

off.

29. Use extra caution when making a “Pocket Cut”

into existing walls or other blind areas. The

protruding blade may cut objects that can cause

KICKBACK.

NEVER place your hand or fingers behind the saw

(Fig. 3). If kickback occurs, the saw could easily

jump backwards over your hand, possibly causing

severe injury.

30. WARNING: It is important to support the work

piece properly and to hold the saw firmly to

prevent loss of control which could cause personal

injury. Fig. 4 illustrates typical hand support of the

saw.

31. Place the wider portion of the saw base on that

part of the work piece which is solidly supported,

not on the section that will fall off when the cut

is made. As examples, Fig. 5 illustrates the RIGHT

way to cut off the end of board, and Fig. 6 the

WRONG way. If the work piece is short or small,

clamp is down.

DON’T TRY TO HOLD SHORT PLACES BY HAND!

32. Never attempt to saw with the circular saw held

upside down in a vise. This is extremely dangerous

and can lead to serious accidents. (Fig. 7)

33. When the brake becomes ineffective, replace the

carbon brushes with new ones.

SPECIFICATIONS

POWER TOOL

CHARGER

Model UC24YFA

Charging voltage 7.2 – 24V

Weight 0.6 kg

Model C6DD

No-load speed 2600 min

–1

Capacity Cutting depth

90° 55 mm

45° 40 mm

Rechargeable battery Ni-Cd battery, 18V

Light bulb 12V, 5W

Weight 4.4 kg

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch gsb 24 ve-2 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info