Bedienungsanleitung Bosch GSC 12V-13 (Seite 13 von 179) (Alle Sprachen)

786167

Zoom out

Zoom in

Vorherige Seite

1/179

Nächste Seite

English | 13

When necessary and while wearing gloves, press bending

sheet parts away from your body.

Apply the machine to the workpiece only when switched on.

80–90°

Guide the power tool at an angle of 80° to 90° to the surface

of the sheet metal and do not tilt it to the side.

Guide the power tool evenly, pushing it gently in the cutting

direction. Applying too much pressure to the power tool will

significantly reduce the service life of application tools and

can damage the power tool.

When cutting curves, make sure not to tilt the power tool lat-

erally and work with low feed rate only.

Maximum steel sheet cutting capacity

The maximum steel sheet cutting capacity dmax depends on

the strength properties of the material to be cut.

The power tool allows for cutting of metal sheet to the follow-

ing thicknesses:

Material max. strength

(N/mm2)dmax

(mm)

Steel 400 1.3

600 0.8

800 0.6

Aluminium 200 2.0

Adjusting cutter clearance "a"

The cutter clearancea (gap between the

cutters) depends on the sheet thickness

dmax to be cut.

The clearance a between the cutters should be 10% of the

maximum sheet thickness (e.g. 0.1mm cutter clearance for

1mm sheet thickness).

For softer or more ductile materials, the clearancea must be

decreased; for harder or more brittle materials, it must be in-

creased.

Loosen the fastening screw(12) for the bottom cutter. Ad-

just the requested cutter clearance a with the set screw(11)

for the bottom cutter. The upper cutter(9) and the bottom

cutter(10) may not touch each other.

Check the clearance using the setting gauge(13). Retighten

the fastening screw(12) for the bottom cutter to a tighten-

ing torque of3–4Nm.

Temperature Dependent Overload Protection

In normal conditions of use, the power tool cannot be over-

loaded. If the power tool is overloaded or the battery tem-

perature is outside the permitted range, the stroke rate is re-

duced or the power tool shuts down. When the stroke rate is

reduced, the power tool will not run at the full stroke rate

again until the battery temperature is back within the permit-

ted range. In the event of automatic shutdown, switch off the

power tool and allow the battery to cool down before switch-

ing the tool on again.

Recommendations for Optimal Handling of the Battery

Protect the battery against moisture and water.

Only store the battery within a temperature range of −20 to

50°C. Do not leave the battery in your car in the summer, for

example.

Occasionally clean the ventilation slots on the battery using a

soft brush that is clean and dry.

A significantly reduced operating time after charging indic-

ates that the battery has deteriorated and must be replaced.

Follow the instructions on correct disposal.

Maintenance and Service

Maintenance and Cleaning

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

uTo ensure safe and efficient operation, always keep

the power tool and the ventilation slots clean.

Changing the cutter (seefigureA)

The upper cutter(9) and the bottom cutter(10) are

identical, have four cutting edges each, and can be ex-

changed with each other.

Turn or replace the cutters in good time. Only sharp applica-

tion tools achieve good cutting capacity and make the power

tool last longer.

To replace the upper cutter(9) loosen the fastening

screw(8), to replace the bottom cutter(10) loosen the

fastening screw(12).

Turn the cutter by 90° or install a new cutter. When installing

the bottom cutter(10), ensure that it fits against the set

screw(11).

Note: Turn the cutter only in the direction indicated in the

figureA and only insert a new cutter in the position shown in

the figure. Cutting is not possible with an incorrectly inser-

ted cutter.

Retighten the fastening screw(8) for the upper cutter and

the fastening screw(12) for the bottom cutter with a tight-

ening torque of 3–4Nm. Check the cutter clearance a as de-

scribed above.

Upper cutter(9) and bottom cutter(10) may not be re-

ground.

Bosch Power Tools 1 609 92A 7MM | (27.04.2022)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GSC 12V-13 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info