Bedienungsanleitung Bosch GSC 18V-16 E (Seite 14 von 191) (Alle Sprachen)

786166

Zoom out

Zoom in

Vorherige Seite

1/191

Nächste Seite

14 | English

Material max. strength

(N/mm2)dmax

(mm)

600 1.2

800 0.7

Aluminium 200 2.2

Adjusting cutter clearance "a"

The cutter clearancea (gap between the

cutters) depends on the sheet thickness

dmax to be cut.

The clearance a between the cutters should be 10% of the

maximum sheet thickness (e.g. 0.1mm cutter clearance for

1mm sheet thickness).

For softer or more ductile materials, the clearancea must be

decreased; for harder or more brittle materials, it must be in-

creased.

Loosen the fastening screw(10) for the bottom cutter. Ad-

just the requested cutter clearance a with the set screw(9)

for the bottom cutter. The upper cutter(7) and the bottom

cutter(8) may not touch each other.

Check the clearance with a commercially available setting

gauge. Retighten the fastening screw(10) for the bottom

cutter with a tightening torque of 3–4Nm.

Temperature Dependent Overload Protection

In normal conditions of use, the power tool cannot be over-

loaded. If the power tool is overloaded or the battery tem-

perature is outside the permitted range, the stroke rate is re-

duced or the power tool shuts down. When the stroke rate is

reduced, the power tool will not run at the full stroke rate

again until the battery temperature is back within the permit-

ted range. In the event of automatic shutdown, switch off the

power tool and allow the battery to cool down before switch-

ing the tool on again.

Maintenance and Service

Maintenance and Cleaning

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

uTo ensure safe and efficient operation, always keep

the power tool and the ventilation slots clean.

Changing the cutter (seefigureA)

The upper cutter(7) and the bottom cutter(8) are identical,

have four cutting edges each, and can be exchanged with

each other.

Turn or replace the cutters in good time. Only sharp applica-

tion tools achieve good cutting capacity and make the power

tool last longer.

To replace the upper cutter(7) loosen the fastening

screw(6), to replace the bottom cutter(8) loosen the

fastening screw(10).

Turn the cutter by 90° or install a new cutter. When installing

the bottom cutter(8), ensure that it fits against the set

screw(9).

Note: Turn the cutter only in the direction indicated in the

figureA and only insert a new cutter in the position shown in

the figure. Cutting is not possible with an incorrectly inser-

ted cutter.

Retighten the fastening screw(6) for the upper cutter and

the fastening screw(10) for the bottom cutter with a tight-

ening torque of 3–4Nm. Check the cutter clearance a as de-

scribed above.

Upper cutter(7) and bottom cutter(8) may not be re-

ground.

After-Sales Service and Application Service

Our after-sales service responds to your questions concern-

ing maintenance and repair of your product as well as spare

parts. You can find explosion drawings and information on

spare parts at: www.bosch-pt.com

The Bosch product use advice team will be happy to help you

with any questions about our products and their accessor-

ies.

In all correspondence and spare parts orders, please always

include the 10‑digit article number given on the nameplate

of the product.

Great Britain

Robert Bosch Ltd. (B.S.C.)

P.O. Box 98

Broadwater Park

North Orbital Road

Denham Uxbridge

UB 9 5HJ

At www.bosch-pt.co.uk you can order spare parts or arrange

the collection of a product in need of servicing or repair.

Tel. Service: (0344) 7360109

E-Mail: boschservicecentre@bosch.com

You can find further service addresses at:

www.bosch-pt.com/serviceaddresses

Transport

The recommended lithium-ion batteries are subject to legis-

lation on the transport of dangerous goods. The user can

transport the batteries by road without further require-

ments.

When shipping by third parties (e.g.: by air transport or for-

warding agency), special requirements on packaging and la-

belling must be observed. For preparation of the item being

shipped, consulting an expert for hazardous material is re-

quired.

Dispatch battery packs only when the housing is undam-

aged. Tape or mask off open contacts and pack up the bat-

tery in such a manner that it cannot move around in the

1 609 92A 7XM | (26.07.2022) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GSC 18V-16 E Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info