Bedienungsanleitung Bosch GSC 75-16 Professional (Seite 9 von 128) (Alle Sprachen)

640562

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

English | 9

Bosch Power Tools 1 609 92A 1S7 | (22.1.16)

 Maintain power tools. Check for misalignment or bind-

ing of moving parts, breakage of parts and any other

condition that may affect the power tool’s operation. If

damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

 Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind

and are easier to control.

 Use the power tool, accessories and tool bits etc. in ac-

cordance with these instructions, taking into account

the working conditions and the work to be performed.

Use of the power tool for operations different from those

intended could result in a hazardous situation.

Service

 Have your power tool serviced by a qualified repair per-

son using only identical replacement parts. This will en-

sure that the safety of the power tool is maintained.

Safety Warnings for Sheet Metal Shears

 The power tool is not suitable for stationary operation.

For example, it may not be clamped in a vice or fastened on

a workbench.

 Only work with the chip deflector 2 mounted. Take care

that the chip deflector is not damaged or bent. Danger of

injury when working without the chip deflector or when it is

damaged. Have a damaged chip deflector replaced immedi-

ately by an after-sales service centre for Bosch power tools.

 Wear protective gloves while working and pay particu-

lar attention to the mains cable. Take care that cut

sheet parts do not bend toward your body or the mains

cable. Sharp burrs develop at the cut steel sheet and can

cause injuries to the operator or damage the mains cable.

If required, press bending steel sheet parts away from your

body or the mains cable using gloves.

 Secure the workpiece. A workpiece clamped with clamp-

ing devices or in a vice is held more secure than by hand.

 Always wait until the machine has come to a complete

stop before placing it down. The tool insert can jam and

lead to loss of control over the power tool.

 Never use the machine with a damaged cable. Do not

touch the damaged cable and pull the mains plug when

the cable is damaged while working. Damaged cables in-

crease the risk of an electric shock.

 Products sold in GB only: Your product is fitted with a

BS 1363/A approved electric plug with internal fuse

(ASTA approved to BS 1362).

If the plug is not suitable for your socket outlets, it should

be cut off and an appropriate plug fitted in its place by an

authorised customer service agent. The replacement plug

should have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible

shock hazard and should never be inserted into a mains

socket elsewhere.

Products sold in AUS and NZ only: Use a residual current

device (RCD) with a rated residual current of 30 mA or

less.

Product Description and

Specifications

Read all safety warnings and all instruc-

tions. Failure to follow the warnings and in-

structions may result in electric shock, fire

and/or serious injury.

While reading the operating instructions, unfold the graphics

page for the machine and leave it open.

Intended Use

The power tool is intended for cutting sheet metals without loss

due to metal chips. It is suitable for curved and straight cuts.

Product Features

The numbering of the product features refers to the illustra-

tion of the machine on the graphics page.

1 On/Off switch

2 Chip deflector

3 Handle (insulated gripping surface)

4 Fastening screw for upper cutter

5 Upper cutter

6 Bottom cutter

7 Adjustment screw, bottom cutter

8 Fastening screw for bottom cutter

9 Hex key*

*Accessories shown or described are not part of the standard de-

livery scope of the product. A complete overview of accessories

can be found in our accessories program.

Noise/Vibration Information

Sound emission values determined according to

EN 60745-2-8.

Typically the A-weighted noise levels of the product are:

Sound pressure level 87 dB(A); Sound power level 98 dB(A).

Uncertainty K =3 dB.

Wear hearing protection!

Vibration total values a

(triax vector sum) and uncertainty K

determined according to EN 60745-2-8: a

=6m/s

K<1.5m/s

The vibration level given in this information sheet has been

measured in accordance with a standardised test given in

EN 60745 and may be used to compare one tool with another.

It may be used for a preliminary assessment of exposure.

The declared vibration emission level represents the main ap-

plications of the tool. However if the tool is used for different ap-

plications, with different accessories or insertion tools or is

poorly maintained, the vibration emission may differ. This may

significantly increase the exposure level over the total working

period.

An estimation of the level of exposure to vibration should also

take into account the times when the tool is switched off or

when it is running but not actually doing the job. This may signif-

icantly reduce the exposure level over the total working period.

Identify additional safety measures to protect the operator from

the effects of vibration such as: maintain the tool and the acces-

sories, keep the hands warm, organisation of work patterns.

OBJ_BUCH-2740-001.book Page 9 Friday, January 22, 2016 9:39 AM

Bosch GSC 75-16 Professional Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info