Bedienungsanleitung Bosch GSH 27 (Seite 13 von 65) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

78422

Zoom out

Zoom in

Vorherige Seite

1/65

Nächste Seite

English–3

1 619 929 E45 • 9.5.06

Noise/Vibration Information

Measured values determined according to EN 60745.

Typically the A-weighted noise level of the machine is:

sound pressure level 95 dB(A); sound power level

106 dB(A). Uncertainty K=3 dB.

Wear hearing protection!

Overall vibrational values (vector sum of three direc-

tions) determined according to EN 60745:

Chiselling: Vibration emission value a

=19 m/s

uncertainty K=2 m/s

The vibration emission level given in

this information sheet has been meas-

ured in accordance with a standardised test given in

EN 60745 and may be used to compare one tool with

another.

The vibration emission level will vary because of the

ways in which a power tool can be used and may

increase above the level given in this information sheet.

This could lead to a significant underestimate of expo-

sure when the tool is used regularly in such a way.

Note: To be accurate, an estimation of the level of

exposure to vibration experienced during a given period

of work should also take into account the times when

the tool is switched off and when it is running but not

actually doing the job. This may significantly reduce the

exposure level over the total working period.

Declaration of Conformity

We declare under our sole responsibility that this prod-

uct is in conformity with the following standards or

standardization documents: EN 60745 according to

the provisions of the directives 89/336/EEC,

98/37/EC, 2000/14/EC.

2000/14/EC: The guaranteed sound power level L

is below 108 dB(A). The valuation procedure for the

conformity is in accordance with appendix VI.

Designated testing authority:

TÜV NORD CERT GmbH & Co. KG,

Am TÜV 1, 30519 Hannover

Leinfelden, 02.02.2006

Robert Bosch GmbH, Power Tools Division

Assembly

Changing the Tool

f Before any work on the machine itself, pull

the mains plug.

Clean the tool shank 5 and apply a light coat of grease.

Tools without Shoulder (see figures A–B)

Pivot the tool retainer 3 upward by approx. 150° and

insert the tool into the tool holder 4.

Pivot the tool retainer 3 down to lock the tool.

Check the latching by pulling the tool.

Tools with Shoulder (see figures C–D)

Tools with an insertion length of 152 mm (6") to the

shoulder can be used.

Pivot the tool retainer 3 upward by approx. 180° and

insert the tool into the tool holder 4.

Pivot the tool retainer 3 back to the tool to lock it. The

shoulder 6 must be held by the tool retainer 3.

Check the latching by pulling the tool.

Operation

Starting Operation

f Observe correct mains voltage! The voltage of

the power source must agree with the voltage

specified on the nameplate of the machine.

Power tools marked with 230 V can also be

operated with 220 V.

Switching On and Off

To start the machine, press the On/Off switch 1 and

keep it depressed.

To switch off the machine, release the On/Off switch

For low temperatures, the machine reaches the full

impact rate only after a certain time.

This start-up time can be shortened by striking the

chisel in the machine against the floor one time.

Operating Instructions

For the highest possible impact damping, work only

with moderate pressure.

Sharpening Chisels

Good results are only achieved with sharp chisels;

therefore, sharpen the chiselling tools in good time.

This ensures a long service life of the tools and good

working performance.

Dr. Egbert Schneider

Senior Vice President

Engineering

Dr. Eckerhard Strötgen

Head of Product

Certification

WARNING

OBJ_BUCH-144-001.book Page 3 Tuesday, May 9, 2006 9:41 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GSH 27 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info