Bedienungsanleitung Bosch GSH 7 VC (Seite 9 von 152) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544259

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

English | 9

Bosch Power Tools 1 609 92A 031 | (26.9.13)

Hammer Safety Warnings

 Wear ear protectors. Exposure to noise can cause hear-

ing loss.

 Use auxiliary handle(s), if supplied with the tool. Loss

of control can cause personal injury.

 Hold power tool by insulated gripping surfaces, when

performing an operation where the cutting accessory

may contact hidden wiring or its own cord. Cutting ac-

cessory contacting a “live” wire may make exposed metal

parts of the power tool “live” and could give the operator an

electric shock.

Products sold in GB only: Your product is fitted with an

BS 1363/A approved electric plug with internal fuse (ASTA

approved to BS 1362).

If the plug is not suitable for your socket outlets, it should be

cut off and an appropriate plug fitted in its place by an author-

ised customer service agent. The replacement plug should

have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible

shock hazard and should never be inserted into a mains sock-

et elsewhere.

Products sold in AUS and NZ only: Use a residual current de-

vice (RCD) with a rated residual current of 30 mA or less.

Additional Safety and Working In-

structions

 Observe the mains voltage! The voltage of the power

source must correspond with the data on the type plate

of the machine.

 Use appropriate detectors to determine if utility lines

are hidden in the work area or call the local utility compa-

ny for assistance. Contact with electric lines can lead to fire

and electric shock. Damaging a gas line can lead to explo-

sion. Penetrating a water line causes property damage.

 Firmly tighten the auxiliary handle, hold the machine

firmly with both hands while working and keep proper

footing and balance at all times. The machine is securely

guided with both hands.

 Insert the SDS-max application tool: Check the latching

by pulling the tool.

 Replace a damaged dust protection cap immediately.

The dust protection cap largely prevents the penetration of

drilling dust into the tool holder during operation. When in-

serting the tool, pay attention that the dust protection cap

is not damaged.

 Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health and cause allergic reactions, lead to res-

piratory infections and/or cancer. Materials containing

asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suita-

ble for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

 To save energy, only switch the power tool on when using it.

 Always wait until the machine has come to a complete

stop before placing it down. The tool insert can jam and

lead to loss of control over the power tool.

 Restarting Protection

In chiselling mode, the restarting protection prevents un-

controlled starting of the machine after a power failure.

– To restart the operation, switch the On/Off switch to

the Off position and start the machine again.

Products sold in GB only: Your product is fitted with an

BS 1363/A approved electric plug with internal fuse (ASTA

approved to BS 1362).

If the plug is not suitable for your socket outlets, it should be

cut off and an appropriate plug fitted in its place by an author-

ised customer service agent. The replacement plug should

have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible

shock hazard and should never be inserted into a mains sock-

et elsewhere.

Products sold in AUS and NZ only: Use a residual current de-

vice (RCD) with a rated residual current of 30 mA or less.

Symbols

The following symbols are important for reading and under-

standing the operating instructions. Please take note of the

symbols and their meaning. The correct interpretation of the

symbols will help you to use the machine in a better and safer

manner.

Symbol Meaning

GSH 7 VC:

Demolition Hammer

Grey-marked area: Handle

(insulated gripping surface)

Article number

Read all safety warnings and all instruc-

tions

Before any work on the machine itself,

pull the mains plug from the socket out-

let

Wear protective gloves

Always wear ear protection.

Wear safety glasses/goggles

OBJ_BUCH-1851-002.book Page 9 Thursday, September 26, 2013 4:08 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GSH 7 VC Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info