Bedienungsanleitung Bosch GSK 64-34 (Seite 17 von 218) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544372

Zoom out

Zoom in

Vorherige Seite

1/218

Nächste Seite

English | 17

Bosch Power Tools 1 609 929 X30 | (22.3.11)

Noise/Vibration Information

Measured noise values determined according to EN 12549.

Typically the A-weighted noise levels of the pneumatic tool are: Sound

pressure level 102 dB(A); sound power level 115 dB(A). Uncertainty

K=2dB.

Wear hearing protection!

Overall vibrational values determined according to EN ISO 20643:

Vibrational emission value a

<2.5m/s

. Uncertainty K =1.5 m/s

Declaration of Conformity

We declare under our sole responsibility that the product described un-

der “Technical data” is in conformity with the following standards or

standardization documents: EN 792 according to the provisions of the di-

rectives 2006/42/EC.

Technical file at:

Robert Bosch GmbH, PT/ESC,

D-70745 Leinfelden-Echterdingen

Robert Bosch GmbH, Power Tools Division

D-70745 Leinfelden-Echterdingen

Leinfelden, 22.03.2011

Assembly

Connecting the Air Supply (see figure A)

Make sure that the pressure of the compressed-air system is below the

maximum permitted rated pressure of the pneumatic tool. Firstly, set the

air pressure to the lower value of the recommended rated pressure (see

“Technical Data”).

When in doubt, check the pressure at the air inlet with a pressure gauge

with the pneumatic tool switched on.

For maximum performance, the values for the supply-air hose 15 (con-

nection thread, maximum operating pressure, inner hose diameter, max-

imum hose length; see “Technical Data”) must be observed.

The compressed air supplied should be free of foreign material and mois-

ture to protect the tool from damage, contamination, and the formation of

rust.

All fittings, connecting lines and hoses must be dimensioned for the pres-

sure and the required air volume.

Avoid restrictions in the air supply, e.g., from pinching, kinking, or

stretching!

Connecting the Air Supply to the Pneumatic Tool

– Empty the magazine 10.

(See “Emptying the Magazine”, page 18)

For the following worksteps, a fastener can be discharged when interi-

or parts of the pneumatic tool are not in the starting position due to re-

pairs, maintenance or transport.

– Connect the air connector 8 with a supply-air hose 15 equipped with an

air-connection coupling 14.

– Check the proper function by placing the outlet 13 or the rubber work-

piece protector 1 of the pneumatic tool onto a piece of scrap wood or

wood material, and discharging once or twice.

Loading the Magazine (see figures B1–B4)

Disconnect the air supply before making any adjust-

ments, changing accessories, or placing the pneumatic

tool aside. This safety measure prevents accidental start-

ing of the pneumatic tool.

fUse only original Bosch accessories (see “Technical Data”). The

precision parts of the pneumatic tool such as the magazine, the outlet

and the shot duct are matched to Bosch staples, nails and brads. Other

manufacturers use other steel qualities and sizes.

Using fasteners not permitted, can damage the pneumatic tool and

cause injuries.

While loading the magazine, hold the pneumatic tool in such a manner

that the outlet 13 is not pointed at your own body or at other persons.

– Clean and lubricate the magazine slider 11 as required and make sure

that the magazine 10 is not dirty/soiled.

– Insert a fitting nail strip 16 in the T-slot at the end of the magazine 10.

When doing this, the nail tips must be inserted first.

– Push the nail strip in the magazine toward the front until the last nail is

positioned in front of the magazine spring 17.

Note: A lock function of the magazine slider prevents the pneumatic tool

from being started with an empty magazine. The discharge lock-off can-

not be pressed in and blank firing is thus prevented.

– Press the pretensioned nail pusher 18 against the magazine slider 11

and at the same time, pull the magazine slider completely to the end of

the magazine 10.

Note: The magazine slider must slide back with only low force (finger-

pressure). A tight-running magazine slider causes the nails to be driven in

at an incorrect angle.

– With the nail pusher 18 pressed, carefully guide the magazine slider 11

toward the front until the nail pusher is over the last nail, thus pushing

the nail strip in the magazine completely to the front.

Note: Do not let the magazine slider snap back without guiding it. Other-

wise, the magazine slider could become damaged, and there is danger of

your fingers being caught or pinched.

Rated pressure

bar 4–8

Connecting thread

"3/8

Supply-air hose

– Max. operating pressure at 20 °C

– Inner diameter of hose

–Max. hose length

bar

3/8

Air consumption per driving proce-

dure

at 6.8 bar (100 psi)

l1.46

Dimensions

–Height

–Width

–Length

307

320

Weight according to EPTA-Procedure

01/2003

kg 1.86

Dr. Egbert Schneider

Senior Vice President

Engineering

Dr. Eckerhard Strötgen

Head of Product

Certification

Compressed-air nailer GSK 64-34

Professional

OBJ_BUCH-1302-001.book Page 17 Tuesday, March 22, 2011 11:17 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GSK 64-34 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info