Bedienungsanleitung Bosch GSL 2 Professional (Seite 16 von 208) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

591980

Zoom out

Zoom in

Vorherige Seite

1/208

Nächste Seite

16 | English

1 609 92A 0L2 | (3.6.14) Bosch Power Tools

compromised. Following a hard knock or fall, carry out a

check by comparing the laser lines or plumb beams with a

known horizontal or vertical reference line or verified per-

pendicular points.

 Switch the measuring tool off during transport. When

switching off, the levelling unit, which can be damaged in

case of intense movement, is locked.

Setting Up the Measuring Tool

Set up the measuring tool on the floor surface to be checked,

ensuring that it is firmly positioned.

The levelling accuracy can be influenced through the ambient

temperature. Especially temperature differences occurring

from the ground upward can deflect the laser beam. As the

thermal layering is greatest at ground level, the measuring

tool should always be set up in the centre of the floor surface

to be checked.

Switching On and Off

To switch on the measuring tool, slide the On/Off switch 8 to

the “On” position. Immediately after switching on, the meas-

uring tool sends laser beams out of the exit openings 1.

 Do not direct the laser beam at persons or animals (es-

pecially not at their eye level), and do not stare into the

laser beam yourself (not even from a distance).

To switch off the measuring tool, slide the On/Off switch 8 to

the “Off” position. When switching off, the levelling unit is

locked.

When the measuring tool is not moved or remote-controlled

for approx. 30 minutes, it switches off automatically to save

the batteries or the battery pack.

After switching off automatically, switch the measuring tool

off via On/Off switch 8 and then on again, if required.

GSL 2 Set: After switching off automatically, the measuring

tool can be switched on again by pressing any button on the

remote control.

 Do not leave the switched-on measuring tool unattend-

ed and switch the measuring tool off after use. Other

persons could be blinded by the laser beam.

When exceeding the maximum permitted operating tempera-

ture of 50 °C, the measuring tool switches off to protect the

laser diode. After cooling down, the measuring tool is ready

for operation and can be switched on again.

Operation with battery pack: The “Electronic Cell Protec-

tion (ECP)” protects the lithium-ion battery pack against deep

discharging. When the battery pack is discharged, the meas-

uring tool is switched off by a protective circuit.

When the measuring tool switches off automatically due to a

discharged battery pack, switch the measuring tool off with

the On/Off switch 8. Charge the battery pack before switch-

ing the measuring tool on again. Otherwise, the battery pack

could become damaged.

Allowing the Measuring Tool to Level In

After switching on, the levelling function automatically com-

pensates irregularities within the self-levelling range of ±4°.

The levelling is finished as soon as the laser beams do not

move any more.

If the automatic levelling function is not possible, e.g.

because the surface on which the measuring tool stands

deviates by more than 4° from the horizontal plane, the laser

beams flash.

Set up the measuring tool in level position and wait for the

self-levelling to take place. As soon as the measuring tool is

within the self-levelling range of ±4°, the laser beams light up

continuously.

In case of ground vibrations or position changes during oper-

ation, the measuring tool is automatically levelled in again,

yet, possibly to a different height when larger position chang-

es are the case. Upon re-levelling, check if the two laser

beams are aligned at the reference point (see “Aligning the

Height of the Measuring Tool”, page 16) in order to avoid ver-

tical errors.

Aligning the Height of the Measuring Tool

The measuring tool generates two laser beams that can be

seen on the floor surface in front of the measuring tool for dis-

tances beyond 50 cm. The beams must be brought into align-

ment at this reference point, where they can initially be seen

on the floor surface. For this, turn the thumbwheel for height

adjustment 9 clockwise or anticlockwise, until both laser

beams overlap at the reference point and only one beam can

be seen.

When the two laser beams cannot be aligned by turning the

thumbwheel, the position of the measuring tool is significant-

ly above or below the floor surface. Position the measuring

tool at a different location on the floor surface with less height

deviation and align the laser beams there.

Starting Operation of the Remote Control

(GSL 2 Set)

 Protect the remote control against moisture and direct

sunlight.

 Do not subject the remote control to extreme tempera-

tures or variations in temperature. As an example, do

not leave it in vehicles for longer periods. In case of large

variations in temperature, allow the remote control to ad-

just to the ambient temperature before putting it into oper-

ation.

The remote control remains ready for operation as long as a

battery with sufficient voltage is inserted.

The signals of the remote control should reach the reception

lens 4 directly from the front and inclined from above. When

the remote control cannot be pointed directly against a recep-

tion lens, the working range is reduced. By reflecting the sig-

nal (e.g. against walls), the working range can be improved,

even for indirect signals.

Switching the measuring tool on via the remote control after

automatic shut-off of the measuring tool is only possible when

the On/Off switch 8 is still in the “On” position. Switching the

measuring tool off with the remote control is not possible.

OBJ_BUCH-1545-006.book Page 16 Tuesday, June 3, 2014 4:54 PM

Bosch GSL 2 Professional Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info