Bedienungsanleitung Bosch GSR 10.8 V-EC TE Professional (Seite 14 von 163) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

591830

Zoom out

Zoom in

Vorherige Seite

1/163

Nächste Seite

14 | English

2 609 141 186 | (9.12.14) Bosch Power Tools

Operation

Starting Operation

Inserting the battery

 Use only original Bosch lithium-ion batteries with the

voltage listed on the nameplate of your power tool.

Using other batteries can lead to injuries and pose a fire

hazard.

Note: Use of batteries not suitable for the machine can lead to

malfunctions of or cause damage to the power tool.

Set the rotational direction switch 5 to the centre position in

order to avoid unintentional starting. Insert the charged bat-

tery 7 into the handle so that it can be felt to engage and faces

flush against the handle.

Reversing the rotational direction

The rotational direction switch 5 is used to reverse the rota-

tional direction of the machine. However, this is not possible

with the On/Off switch 10 actuated.

Rotate clockwise: Move the rotational direction switch 5

on both sides up to the stop into position .

Rotate anticlockwise: Move the rotational direction

switch 5 on both sides up to the stop into position .

Switching On and Off

To start the machine, press the On/Off switch 10 and keep it

pressed.

The LED 12 lights up when the On/Off switch 10 is halfway or

fully pressed, and enables illumination of the screwing loca-

tion in unfavourable light conditions.

To switch off the machine, release the On/Off switch 10.

To save energy, only switch the power tool on when using it.

Adjusting the Speed

The speed of the switched-on power tool can be variably ad-

justed, depending on how far the On/Off switch 10 is

pressed.

Light pressure on the On/Off switch 10 results in a low rota-

tional speed. Further pressure on the switch results in an in-

crease in speed.

Adjusting the Screw-in Depth (see figure B)

With the adjustment sleeve 3, the screw-in depth of the screw

head into the workpiece can be preset in 8 locking steps per

full turn. Each step corresponds with a 0.25 mm change of

the screw-in depth.

Turning the adjustment sleeve 3 in clockwise direction results

in a greater screw-in depth; turning in anticlockwise direction

reduces the screw-in depth.

The required setting is best determined by testing.

Temperature Dependent Overload Protection

In normal conditions of use, the power tool cannot be over-

loaded. If the power tool is overloaded or not kept within the

permitted battery temperature range, the power output is re-

duced or the power tool is switched off. The power tool will

not run at full power output again until the permitted battery

temperature has been reached.

Protection Against Deep Discharging

The lithium-ion battery is protected against deep discharging

by the “Electronic Cell Protection (ECP)”. When the battery is

empty, the machine is switched off by means of a protective

circuit: The inserted tool no longer rotates.

Working Advice

 Apply the power tool to the screw only when it is

switched off. Rotating tool inserts can slip off.

Guide the screw toward the screwdriving bit 1. The screw is

held in place by the magnet pull of the universal bit holder 11.

Firmly push the tip of the screw into the material to be

screwed until the screwing-depth stop 4 faces against the

workpiece.

Switch the machine on. The screw is screwed into the materi-

al until the adjusted screw-in depth is reached. The drive is

disengaged and the tool holder no longer rotates. Check the

screw-in depth and readjust, if required.

For unscrewing screws, set the rotational direction switch 5

to left rotation and pull off the screwing-depth stop 4 toward

the front without turning the adjustment sleeve.

Working with the screwing-depth stop 4 is also possible when

adapting the screw-in depth.

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine itself (e. g. mainte-

nance, tool change, etc.) as well as during transport

and storage, remove the battery from the power tool.

There is danger of injury when unintentionally actuating

the On/Off switch.

 For safe and proper working, always keep the machine

and ventilation slots clean.

When the battery is no longer operative, please refer to an au-

thorised after-sales service agent for Bosch power tools.

To ensure trouble-free operation of the power tool, clean the

mount of the universal bit holder 11 and the screwing-depth

stop 4 with compressed air at regular intervals.

After-sales Service and Application Service

Our after-sales service responds to your questions concern-

ing maintenance and repair of your product as well as spare

parts. Exploded views and information on spare parts can al-

so be found under:

www.bosch-pt.com

Bosch’s application service team will gladly answer questions

concerning our products and their accessories.

In all correspondence and spare parts order, please always in-

clude the 10-digit article number given on the type plate of

the machine.

OBJ_BUCH-2205-001.book Page 14 Tuesday, December 9, 2014 12:02 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GSR 10.8 V-EC TE Professional Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info