Bedienungsanleitung Bosch GSR 10.8V-35 HX (Seite 11 von 20) (Englisch)

786087

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

English | 11

Cordless Drill/Driver GSB 10.8V-35 GSR 10.8V-35 GSR 10.8V-35 HX

Recommended chargers GAL 12...

GAX 18...

GAL 12...

GAX 18...

GAL 12...

GAX 18...

A) Measured at 20−25°C with rechargeable batteryGBA 10.8V 6.0Ah.

B) Measured withGBA 10.8V 2.0Ah andGBA 10.8V 6.0Ah

Assembly

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Charging the Battery

uUse only the chargers listed in the technical data. Only

these chargers are matched to the lithium-ion battery of

your power tool.

Note: The battery is supplied partially charged. To ensure

full battery capacity, fully charge the battery in the charger

before using your power tool for the first time.

The lithium-ion battery can be charged at any time without

reducing its service life. Interrupting the charging process

does not damage the battery.

The lithium-ion battery is protected against deep discharge

by the "Electronic Cell Protection (ECP)". When the battery

is discharged, the power tool is switched off by means of a

protective circuit: The application tool no longer rotates.

uDo not continue to press the On/Off switch after the

power tool has automatically switched off. The battery

can be damaged.

Follow the instructions on correct disposal.

Removing the battery (see figureA)

To remove the battery (9), press both release buttons (8)

and pull the battery downwards out of the power tool. Do

not use force to do this.

Changing the tool

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Inserting the application tool: GSR 10.8V-35 HX (see

figureC)

Pull the locking sleeve (3) back, guide the application tool

into the tool holder (1) as far as it will go and release the

locking sleeve (3) to lock the application tool.

Please note that the locking interface is optimized for

the most commonly used application tool dimension in

the individual country of use.

Inserting the application tool: GSB 10.8V-35/GSR

10.8V-35 (see figureB)

Open the keyless chuck (2) by turning it in the direction of

rotation ➊ until the tool can be inserted. Insert the tool.

Firmly tighten the keyless chuck (2) by turning it by hand in

the direction of rotation ➋. This will automatically lock the

drill chuck.

The lock will disengage again if you turn the sleeve in the op-

posite direction to remove the tool.

Removing the application tool: GSR 10.8V-35 HX

Pull the locking sleeve (3) back and pull the application tool

out of the holder (1).

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some

wood types, minerals and metal can be harmful to one’s

health. Touching or breathing-in the dust can cause allergic

reactions and/or lead to respiratory infections of the user or

bystanders.

Certain dust, such as oak or beech dust, is considered carci-

nogenic, especially in connection with wood-treatment ad-

ditives (chromate, wood preservative). Materials containing

asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the ma-

terials to be worked.

uAvoid dust accumulation at the workplace. Dust can

easily ignite.

Operation

Starting Operation

Inserting the battery

Note: The use of batteries unsuitable for your power tool can

lead to malfunctions or damage to the power tool.

Set the rotational direction switch (7) to the middle position

to avoid unintentionally switching it on. Insert the charged

battery (9) into the handle until you feel it engage and it is

flush with the handle.

Setting the rotational direction (see figureD)

The rotational direction switch (7) is used to change the ro-

tational direction of the power tool. However, this is not pos-

sible while the on/off switch (10) is being pressed.

Right rotation: To drill and to drive in screws, press the ro-

tational direction switch (7) through to the left stop.

Left rotation: To loosen and unscrew screws, press the ro-

tational direction switch (7) through to the right stop.

Preselecting the Torque

The torque presetting ring (4) can be used to preselect the

required torque in 20 stages. When the correct setting is

Bosch Power Tools 1 609 92A 6G9 | (17.06.2021)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GSR 10.8V-35 HX Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info