Bedienungsanleitung Bosch gsr 12 2 (Seite 23 von 30) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

389177

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

English

Model C6BU C7BU

Voltage 230V

Cutting Depth

90° 54 mm 63 mm

45° 39 mm 45 mm

Power Input 1010W 1150W

No-Load Speed 5000/min

Weight (without cord) 3.5 kg 4.0 kg

SPECIFICATIONS

CAUTION

To avoid possible accident, always ensure that the

portion of lumber remaining after cutting is securely

anchored or held in position.

ADJUSTING THE SAW PRIOR TO USE

1. Adjusting the cutting depth

As shown in Fig. 2, hold the handle with one hand

while loosening the knob with the other.

The cutting depth can be adjusted by moving the base

to the desired position. In such manner adjust the

cutting depth and then securely retighten the knob.

2. Adjusting the riving knife

Loosen the hexagonal – head bolt used to clamp the

riving knife, adjust the riving knife to the position

shown in Fig. 3 and securely retighten the bolt.

3. Adjusting the angle of inclination

As shown in Fig. 4 (A), Fig. 4 (B) by loosening the

knob on the incline gauge and the wing-bolt on the

base, the saw blade may be inclined to a maximum

angle of 45° in relation to the base. After having

completed the adjustment, reconfirm that the knob

and the wing bolt are firmly tightened.

4. Regulating the guide (Fig. 5)

The cutting position can be regulated by moving the

guide to the left or right after loosening its wingbolt.

The guide may be mounted on either the right or left

side of the tool.

5. Adjusting the guide piece

On the circular saw, it is possible to make fine

adjustment of the fixing position of the guide piece,

where the saw blade and the premarked line are to

be aligned.

When the saw is shipped from the factory, the linear

portion of a front scale on the guide piece is aligned

with the central position of the saw blade. (Fig. 6)

Loosen the fixed screw on the guide piece, should

the fixing position be wrong, and make necessary

adjustment of the position.

CUTTING PROCEDURES

1. Place the base on the material, then align the

premarked line and the sawblade with the guide piece

front scale section at the front of the base. (Fig. 6)

When the base is not slanted, use the large cutout as

the guide. (Fig. 6, Fig. 7 (A))

If the base is slanted (45 degrees), use the small front

scale as the guide. (Fig. 6, Fig. 7 (B))

STANDARD ACCESSORIES

(1) Saw Blade (mounted on tool ) ............................... 1

Dia. 165 mm ............................ C6BU

(

Dia. 185 mm ............................ C7BU

)

(2) Box Wrench ............................................................... 1

(3) Guide .......................................................................... 1

(4) Wing-bolt ................................................................... 1

Standard accessories are subject to change without

notice.

OPTIONAL ACCESSORIES (sold separately)

(1) Dust Collector Set (D)

Connect the suction hose to collect saw dust with

the vacuum cleaner (see Fig. 12).

(2) Washer (A)

............. for 16 mm (Hole dia. of saw blade)

............... for 30 mm (Hole dia. of saw blade)

Optional accessories are subject to change without notice.

APPLICATION

Cutting various types of wood.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position. If

the plug is connected to a receptacle while the power

switch is in the ON position, the power tool will start

operating immediately, which could cause a serious

accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be kept

as short as practicable.

4. Prepare a wooden workbench (Fig. 1)

Since the saw blade will extend beyond the lower

surface of the lumber, place the lumber on a

workbench when cutting. If a square block is utilized

as a workbench, select level ground to ensure it is

properly stabilized. An unstable workbench will result

in hazardous operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch gsr 12 2 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info