Bedienungsanleitung Bosch gsr 12 ve-2 (Seite 39 von 46) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

386472

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

English

5. Regulating the guide (Fig. 16)

The cutting position can be regulated by moving

the guide to the left or right after loosening its

wingbolt. The guide may be mounted on either the

right or left side of the tool.

HOW TO USE

1. Operation of switch (Fig. 17)

(switch trigger and light switch)

(1) For safe operation of the machine, a “switch lock”

is provided on the side of a handle.

If the “switch trigger” is pulled in a state where

“switch lock” is pressed in the direction of the

arrow mark, the main switch can be turned ON.

And the “switch lock” is used as the “light switch”.

If the “switch lock (light switch)” is pressed in a

state, the light is turned ON.

(2) After the switch is turned ON, even when you

release your hand from the switch lock, the body

continues running and the light continues being

turned ON as long as you keep on pulling the

switch trigger.

(3) If you release the switch trigger, you can turn OFF

the switch and the “switch lock” returns to the

original position automatically and the light turns

OFF too.

CAUTION:

⅜ Do not fix and secure the switch lock. Besides, keep

your finger off the switch trigger when the circular

saw is being carried around. Otherwise, the main

body switch can be inadvertently turned ON,

resulting in unexpected accidents.

⅜ Keep the light ON during cutting operation only.

If it is lit ON in other cases, the main body switch

can be inadvertently turned ON, resulting in

unexpected accidents.

⅜ If the main body is left as it is with the battery

inserted, there can be a case where the [switch lock]

touches the floor and/or wall surface and lights up

continuously, depending on the direction of the

body. Be careful, since continuous lighting can easily

make a full-charged battery go dead in about 3

hours.”

2. Cutting procedures

CAUTION:

⅜ Recheck that the saw blade is securely clamped.

⅜ Confirm that the knob for adjusting the slot depth,

the knob and the wing bolt for adjusting the angle

of inclination.

(1) Place the base on the material, then align the

premarked line and the sawblade with the guide

piece front scale section at the front of the base.

(Fig. 15)

When the base is not slanted, use the large cutout

as the guide. (Fig. 15, Fig. 18(A))

If the base is slanted (45 degrees), use the small

front scale as the guide. (Fig. 15, Fig. 18(B))

(2) Ensure that the switch is turned to the ON position

before the saw blade comes in contact with the

lumber. The switch is turned ON when the trigger

is squeezed; and OFF when the trigger is released.

Moving the saw straight at a constant speed will

produce optimum cutting.

If the battery is reinserted within 3 seconds, the

battery may not be properly charged.

PRIOR TO OPERATION

1. Setting up and checking the work environment

Check if the work environment is suitable by

following the precautions.

2. Prepare a wooden workbench (Fig. 11)

Since the saw blade will extend beyond the lower

surface of the lumber, place the lumber on a

workbench when cutting. If a square block is utilized

as a workbench, select level ground to ensure it

is properly stabilized. An unstable workbench will

result in hazardous operation.

CAUTION

To avoid possible accident, always ensure that the

portion of lumber remaining after cutting is securely

anchored or held in position.

ADJUSTING THE SAW PRIOR TO USE

CAUTION

Pull out battery before doing any adjusting.

1. Adjusting the cutting depth

As shown in Fig. 12, hold the handle with one hand

while loosening the knob with the other.

The cutting depth can be adjusted by moving the

base to the desired position. In such manner adjust

the cutting depth and then securely retighten the

knob.

2. Adjusting the riving knife

Loosen the hexagonal – head bolt used to clamp

the riving knife, adjust the riving knife to the position

shown in Fig. 13 and securely retighten the bolt.

3. Adjusting the angle of inclination

As shown in Fig. 14 (A), Fig. 14 (B) by loosening

the knob on the incline gauge and the wing-bolt

on the base, the saw blade may be inclined to a

maximum angle of 45° in relation to the base. After

having completed the adjustment, reconfirm that

the knob and the wing bolt are firmly tightened.

NOTE:

Values of the inclined gauge provided on the base

merely serve as a rough guideline. For cutting

operation at an inclined posture, use the circular

saw after adjusting the angle between the base and

the saw blade with a protractor, etc.

4. Adjusting the guide piece

On the circular saw, it is possible to make fine

adjustment of the fixing position of the guide piece,

where the saw blade and the premarked line are

to be aligned.

When the saw is shipped from the factory, the

linear portion of a front scale on the guide piece

is aligned with the central position of the saw blade.

(Fig. 15)

Loosen the fixed screw on the guide piece, should

the fixing position be wrong, and make necessary

adjustment of the position.

NOTE:

For cutting operation at the inclination of 45 degrees,

make adjustment so that the notch on the guide

piece and the premarked line become aligned.

Bosch gsr 12 ve-2 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info