Bedienungsanleitung Bosch GSR 12V-15 FC (Seite 17 von 225) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

708149

Zoom out

Zoom in

Vorherige Seite

1/225

Nächste Seite

English | 17

Operation

Start-up

Inserting the battery

Note: The use of batteries unsuitable for your power tool can

lead to malfunctions or damage to the power tool.

Set the rotational direction switch (6) to the middle position

to avoid unintentionally switching it on. Insert the charged

battery (5) into the handle until you feel it engage and it is

flush with the handle.

Setting the rotational direction (see figureH)

The rotational direction switch (6) is used to change the ro-

tational direction of the power tool. However, this is not pos-

sible while the on/off switch (7) is being pressed.

Right rotation: To drill and to drive in screws, press the ro-

tational direction switch (6) through to the left stop.

Left Rotation: To loosen and unscrew screws and nuts,

press the rotational direction switch (6) through to the right

stop.

Preselecting the Torque

The torque presetting ring (2) can be used to preselect the

required torque in 15 stages. When the correct setting is

used, the application tool will be stopped when the screw is

driven flush into the material or once the set torque has been

reached. In position the overload clutch is deactivated,

e.g. for drilling.

When unscrewing screws, it may be advisable to select a

higher setting or the symbol.

Mechanical gear selection

u Only operate the gear selector switch (3) when the

power tool is not in use.

You can pre-select two speed ranges with the gear selector

switch (3).

Gear I:

Low speed range; for screwdriving or working with a large

drilling diameter.

Gear II:

High speed range; for working with a small drilling diameter.

u Always push the gear selector as far as it will go. Other-

wise, the power tool may become damaged.

Switching on/off

To start the power tool, press and hold the on/off switch

(7).

The worklight (9) lights up when the on/off switch (7) is

lightly or fully pressed, allowing the work area to be illumin-

ated in poor lighting conditions.

The worklight (9) will remain lit for approx. 10 seconds after

the on/off switch (7) has been released.

To save energy, only switch the power tool on when in use.

Adjusting the speed

You can adjust the speed of the power tool when it is on by

pressing in the on/off switch (7) to varying extents.

Applying light pressure to the on/off switch (7) results in a

low rotational speed. Applying increasing pressure to the

switch increases the speed.

Fully automatic spindle lock (Auto-Lock)

The drill spindle, and therefore the holder, are locked when

the on/off switch (7) is not pressed.

This allows screws to be driven in even when the battery is

discharged and enables the power tool to be used as a

screwdriver.

Temperature-dependent overload protection

In normal conditions of use, the power tool cannot be over-

loaded. If the power tool is overloaded or not kept within the

permitted operating temperature range, the power output is

reduced or the power tool is switched off. The power tool

will not run at full power output again until the permitted op-

erating temperature has been reached.

Battery charge indicator

When the on/off switch (7) is pressed in halfway or com-

pletely, the battery charge indicator (8) indicates the state

of charge of the battery for several seconds. The indicator

consists of three green LEDs.

LED Capacity

Continuous lighting 3 x green ≥ 2/3

Continuous lighting 2 x green ≥ 1/3

Continuous lighting 1 x green < 1/3

Flashing light 1 x green Reserve

Practical advice

u Only apply the power tool to the screw when the tool

is switched off. Rotating application tools can slip off.

After working at a low speed for an extended period, you

should operate the power tool at the maximum speed for ap-

proximately three minutes without load to cool it down.

When drilling into metal, only use sharpened HSS drills (HSS

= High-grade high-speed steel) which are in perfect condi-

tion. The Bosch accessory range guarantees appropriate

quality.

Before screwing larger, longer screws into hard materials, it

is advisable to pre-drill a pilot hole with the core diameter of

the thread to approx. 2/3 of the screw length.

Maintenance and servicing

Maintenance and cleaning

u Remove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

u To ensure safe and efficient operation, always keep

the power tool and the ventilation slots clean.

Bosch Power Tools 1 609 92A 4A7 | (11.10.2018)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GSR 12V-15 FC Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info