Bedienungsanleitung Bosch GSR 18 V-EC TE plus MA 55 Professional (Seite 14 von 154) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544118

Zoom out

Zoom in

Vorherige Seite

1/154

Nächste Seite

14 | English

2 609 141 014 | (3.5.13) Bosch Power Tools

Switching On and Off

To start the machine, press the On/Off switch 7 and keep it

pressed.

The LED 12 lights up when the On/Off switch 7 is halfway or

fully pressed, and enables illumination of the screwing loca-

tion in unfavourable light conditions.

To lock the pressed On/Off switch 7, press the lock-on button

To switch off the machine, release the On/Off switch 7 or

when it is locked with the lock-on button 6, briefly press the

On/Off switch 7 and then release it.

To save energy, only switch the power tool on when using it.

Adjusting the Speed

The speed of the switched on power tool can be variably ad-

justed, depending on how far the On/Off switch 7 is pressed.

Light pressure on the On/Off switch 7 results in a low rotation-

al speed. Further pressure on the switch results in an increase

in speed.

Adjusting the Screw-in Depth (see figure B)

With the adjustment sleeve 3, the screw-in depth of the screw

head into the workpiece can be preset in 8 locking steps per

full turn. Each step corresponds with a 0.25 mm change of

the screw-in depth.

Turning the adjustment sleeve 3 in clockwise direction results

in a greater screw-in depth; turning in anticlockwise direction

reduces the screw-in depth.

The required setting is best determined by testing.

Temperature Dependent Overload Protection

When using as intended for, the power tool cannot be subject

to overload. When the load is too high or the allowable battery

temperature range of 0–70 °C is exceeded, the speed is re-

duced. The power tool will not run at full speed until reaching

the allowable battery temperature.

Protection Against Deep Discharging

The Lithium-Ion battery is protected against deep discharging

by the “Electronic Cell Protection (ECP)”. When the battery is

empty, the machine is switched off by means of a protective

circuit: The inserted tool no longer rotates.

Working Advice

 Apply the power tool to the screw only when it is

switched off. Rotating tool inserts can slip off.

Guide the screw toward the screwdriving bit 1. The screw is

held in place by the magnet pull of the universal bit holder 13.

Firmly push the tip of the screw into the material to be

screwed until the screwing-depth stop 4 faces against the

workpiece.

Switch the machine on. The screw is screwed into the materi-

al until the adjusted screw-in depth is reached. The drive is

disengaged and the tool holder no longer rotates. Check the

screw-in depth and readjust, if required.

For unscrewing screws, set the rotational direction switch 5

to left rotation and pull off the screwing-depth stop 4 toward

the front without turning the adjustment sleeve.

Working with the screwing-depth stop 4 is also possible when

adapting the screw-in depth.

Belt Clip

With the belt clip 8, the machine can be hung onto a belt. The

user has both hands free and the machine is always at hand.

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine itself (e. g. mainte-

nance, tool change, etc.) as well as during transport

and storage, remove the battery from the power tool.

There is danger of injury when unintentionally actuating

the On/Off switch.

 For safe and proper working, always keep the machine

and ventilation slots clean.

When the battery is no longer operative, please refer to an au-

thorised after-sales service agent for Bosch power tools.

After-sales Service and Application Service

Our after-sales service responds to your questions concern-

ing maintenance and repair of your product as well as spare

parts. Exploded views and information on spare parts can al-

so be found under:

www.bosch-pt.com

Bosch’s application service team will gladly answer questions

concerning our products and their accessories.

In all correspondence and spare parts order, please always in-

clude the 10-digit article number given on the type plate of

the machine.

Great Britain

Robert Bosch Ltd. (B.S.C.)

P.O. Box 98

Broadwater Park

North Orbital Road

Denham

Uxbridge

UB 9 5HJ

Tel. Service: (0844) 7360109

Fax: (0844) 7360146

E-Mail: boschservicecentre@bosch.com

Ireland

Origo Ltd.

Unit 23 Magna Drive

Magna Business Park

City West

Dublin 24

Tel. Service: (01) 4666700

Fax: (01) 4666888

OBJ_BUCH-1908-001.book Page 14 Friday, May 3, 2013 12:30 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GSR 18 V-EC TE plus MA 55 Professional Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info