Bedienungsanleitung Bosch GSR 18 V-EC TE (Seite 8 von 35) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544117

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

8 | English

2 609 141 015 | (23.5.13) Bosch Power Tools

 Do not continue to press the On/Off switch after the

machine has been automatically switched off. The bat-

tery can be damaged.

The battery is equipped with a NTC temperature control

which allows charging only within a temperature range of be-

tween 0 °C and 45 °C. A long battery service life is achieved

in this manner.

Observe the notes for disposal.

Removing the battery

The battery 9 is equipped with two locking levels that should

prevent the battery from falling out when pushing the battery

unlocking button 10 unintentionally. As long as the battery is

inserted in the power tool, it is held in position by means of a

spring.

To remove the battery 9, press the unlocking button 10 and

pull out the battery toward the front. Do not exert any force.

Changing the Tool (see figure A)

 Before any work on the machine itself (e. g. mainte-

nance, tool change, etc.) as well as during transport

and storage, remove the battery from the power tool.

There is danger of injury when unintentionally actuating

the On/Off switch.

Pull off the screwing-depth stop 4 toward the front. Pull out

the screwdriver bit 1. If required, the universal bit holder 13

can also be pulled off and replaced.

After changing the tool, reattach the screwing-depth stop 4.

Operation

Starting Operation

Inserting the battery

 Use only original Bosch lithium ion batteries with the

voltage listed on the nameplate of your power tool. Us-

ing other batteries can lead to injuries and pose a fire haz-

ard.

Note: Use of batteries not suitable for the machine can lead to

malfunctions of or cause damage to the power tool.

Set the rotational direction switch 5 to the centre position in

order to avoid unintentional starting. Insert the charged bat-

tery 9 into the handle so that it can be felt to engage and faces

flush against the handle.

Reversing the rotational direction

The rotational direction switch 5 is used to reverse the rota-

tional direction of the machine. However, this is not possible

with the On/Off switch 7 actuated.

Rotate clockwise: Move the rotational direction switch 5

on both sides up to the stop into position .

Rotate anticlockwise: Move the rotational direction

switch 5 on both sides up to the stop into position .

Switching On and Off

To start the machine, press the On/Off switch 7 and keep it

pressed.

The LED 12 lights up when the On/Off switch 7 is halfway or

fully pressed, and enables illumination of the screwing loca-

tion in unfavourable light conditions.

To lock the pressed On/Off switch 7, press the lock-on button

To switch off the machine, release the On/Off switch 7 or

when it is locked with the lock-on button 6, briefly press the

On/Off switch 7 and then release it.

To save energy, only switch the power tool on when using it.

Adjusting the Speed

The speed of the switched on power tool can be variably ad-

justed, depending on how far the On/Off switch 7 is pressed.

Light pressure on the On/Off switch 7 results in a low rotation-

al speed. Further pressure on the switch results in an increase

in speed.

Adjusting the Screw-in Depth (see figure B)

With the adjustment sleeve 3, the screw-in depth of the screw

head into the workpiece can be preset in 8 locking steps per

full turn. Each step corresponds with a 0.25 mm change of

the screw-in depth.

Turning the adjustment sleeve 3 in clockwise direction results

in a greater screw-in depth; turning in anticlockwise direction

reduces the screw-in depth.

The required setting is best determined by testing.

Temperature Dependent Overload Protection

When using as intended for, the power tool cannot be subject

to overload. When the load is too high or the allowable battery

temperature range of 0–70 °C is exceeded, the speed is re-

duced. The power tool will not run at full speed until reaching

the allowable battery temperature.

Protection Against Deep Discharging

The Lithium-Ion battery is protected against deep discharging

by the “Electronic Cell Protection (ECP)”. When the battery is

empty, the machine is switched off by means of a protective

circuit: The inserted tool no longer rotates.

Working Advice

 Apply the power tool to the screw only when it is

switched off. Rotating tool inserts can slip off.

Guide the screw toward the screwdriving bit 1. The screw is

held in place by the magnet pull of the universal bit holder 13.

Firmly push the tip of the screw into the material to be

screwed until the screwing-depth stop 4 faces against the

workpiece.

Switch the machine on. The screw is screwed into the materi-

al until the adjusted screw-in depth is reached. The drive is

disengaged and the tool holder no longer rotates. Check the

screw-in depth and readjust, if required.

OBJ_BUCH-1959-002.book Page 8 Thursday, May 23, 2013 8:25 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GSR 18 V-EC TE Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info