Bedienungsanleitung Bosch GSR 18V-110 C (Seite 18 von 257) (Alle Sprachen)

786162

Zoom out

Zoom in

Vorherige Seite

1/257

Nächste Seite

18 | English

The lithium-ion battery can be charged at any time without

reducing its service life. Interrupting the charging process

does not damage the battery.

The lithium-ion battery is protected against deep discharge

by the "Electronic Cell Protection (ECP)". When the battery

is discharged, the power tool is switched off by means of a

protective circuit: The application tool no longer rotates.

uDo not continue to press the On/Off switch after the

power tool has automatically switched off. The battery

can be damaged.

Follow the instructions on correct disposal.

Removing the Battery

The battery (11) is equipped with two locking levels to pre-

vent the battery from falling out when pushing the battery re-

lease button (12) unintentionally. As long as the battery is

inserted in the power tool, it is held in position by means of a

spring.

To remove the battery (11), press the release button (12)

and pull the battery out of the power tool. Do not use force

to do this.

Battery charge indicator

The green LEDs on the battery charge indicator indicate the

state of charge of the battery. For safety reasons, it is only

possible to check the state of charge when the power tool is

not in operation.

Press the button for the battery charge indicator or to

show the state of charge. This is also possible when the bat-

tery is removed.

If no LED lights up after pressing the button for the battery

charge indicator, then the battery is defective and must be

replaced.

Battery model GBA 18V...

LEDs Capacity

3× continuous green light 60−100%

2× continuous green light 30−60%

1× continuous green light 5−30%

1× flashing green light 0−5%

Battery model ProCORE18V...

LEDs Capacity

5× continuous green light 80−100%

4× continuous green light 60−80%

3× continuous green light 40−60%

2× continuous green light 20−40%

1× continuous green light 5−20%

LEDs Capacity

1× flashing green light 0−5%

Auxiliary handle

uDo not operate your power tool without the auxiliary

handle (4).

uBefore carrying out any work, make sure that the aux-

iliary handle is tightened. Loss of control can cause per-

sonal injury. Ensure that the auxiliary handle is tightened

with a torque suited to the fastening method; fasten this

to the power tool so that any movement of the auxiliary

handle around or along the drilling axis is avoided.

Fitting the auxiliary handle

To open the auxiliary handle, turn the lower gripping end of

the auxiliary handle (4) in an anticlockwise direction.

Pull back the intermediate piece of the auxiliary handle (5)

and hold it in this position.

Slide the auxiliary handle over the drill chuck to mount the

auxiliary handle on the power tool.

Then let go of the intermediate piece (5).

Afterwards, turn the lower gripping end of the auxiliary

handle (4) clockwise to retighten it.

Swivelling the auxiliary handle

You can swivel the auxiliary handle (4) to any angle for a safe

work posture that minimises fatigue.

Turn the lower gripping end of the auxiliary handle (4) anti-

clockwise and swivel the auxiliary handle (4) into the re-

quired position. Afterwards, turn the lower gripping end of

the auxiliary handle (4) clockwise to retighten it.

Setting the drilling depth

You can use the depth stop(3) to set the required drilling

depth X.

Loosen the wing bolt for adjusting the depth stop (6) and in-

sert the depth stop into the auxiliary handle (4).

Pull the depth stop(3) far enough out that the distance

between the drill bit tip and the edge of the depth stop(3)

corresponds to the required drilling depth X.

Retighten the wing bolt for adjusting the depth stop (6).

Changing the tool (see figure A)

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

The drill spindle is locked when the on/off switch (17) is not

pressed. This makes it possible to change the application

tool in the drill chuck quickly, conveniently and easily.

Open the keyless chuck (2) by turning it in the direction of

rotation  until the tool can be inserted. Insert the tool.

Firmly tighten the keyless chuck (2) by turning it by hand in

the direction of rotation . This will automatically lock the

drill chuck.

1 609 92A 837 | (14.07.2022) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GSR 18V-110 C Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info