Bedienungsanleitung Bosch gsr 6-40te (Seite 10 von 45) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

381188

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

English - 2

Observe correct mains voltage: The voltage of

the power source must agree with the voltage

specified on the nameplate of the machine.

Equipment marked with 230 V can also be con-

nected to 220 V.

Switching On and Off

To start the machine press the On/Off switch 6.

The machine runs with variable

speed between 0 and maximum,

depending on the pressure applied

to the On/Off switch 6. Light pres-

sure results in a low rotational

speed thus allowing smooth, con-

trolled starts.

Lock the pushed On/Off switch 6 by pressing the

lock-on button 5.

To switch off the machine, release the On/Off

switch 6 or push and release it then.

Reversing the Rotational Direction

Operate the rotational direction

switch 7 only at a standstill.

Set rotational direction selector 7 to R (right or

clockwise) or L (left or anticlockwise). (Rotational

direction selector 7 is locked when On/Off

switch 6 is activated).

To change the screwdriver blade 1, pull off the

depth stop 2 to the front. The preselected screw-

ing depth is altered as a result.

With the adjustment collar 3, the screwing depth

of the screw head in the material can be prese-

lected in 8 indented steps per revolution (of

0.2 mm each):

Slide the adjustment collar 3 forward to the stop.

Set screwing depth by rotating the adjustment

collar 3:

Clockwise = Increased screwing depth

Counter-clockwise = Decreased screwing depth

Then slide the adjustment collar 3 backward to

the stop.

The required setting can best be determined by a

trial screw driving.

The screw is held by the magnetic universal

holder (Type GSR 6-25 TE / GSR 6-40 TE).

Press the point of the screw firmly against the

material to be screwed until the depth stop 2

rests against the material and the screw driving

insert disengages.

To loosen screws, set the reversing switch 7 to

counter-clockwise and pull off the depth stop 2 to

the front.

With the belt clip 4, the machine can be hung

onto a belt. The user has both hands free and the

machine is always at hand.

Before any work on the machine itself, pull

the mains plug.

For safe and proper working, always keep the

machine and the ventilation slots clean.

If the machine should fail despite the care taken

in manufacturing and testing procedures, repair

should be carried out by an after-sales service

centre for Bosch power tools.

In all correspondence and spare parts orders,

please always include the 10-digit order number

given on the nameplate of the machine.

WARNING! Important instructions for con-

necting a new 3-pin plug to the 2-wire cable.

The wires in the cable are coloured according to

the following code:

Do not

connect the blue or brown wire to the

earth terminal of the plug.

Important: If for any reason the moulded plug is

removed from the cable of this machine, it must

be disposed of safely.

Initial Operation

Changing the Tool

Depth Stop

Belt clip

Maintenance and Cleaning

strain relief

live = brown

neutral = blue

To be fitted

by qualified

professional only

10 • 3 609 929 623 • TMS • 14.03.03

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch gsr 6-40te Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info