Bedienungsanleitung Bosch GSS 140 A (Seite 13 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

78695

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

English | 13

Bosch Power Tools 2 609 140 834 | (11.4.11)

Position the sanding sheet 4 flush alongside one edge of the

sanding plate 2, then lay the sanding sheet onto the sanding

plate and press firmly.

To remove the sanding sheet 4, grasp it at one of the tips and

pull it off from the sanding plate 2.

Sanding Sheets without Velcro Backing

(see figure A— C)

n Press the release button 5 and keep it depressed.

o Guide the sanding sheet 4 to the stop under the opened

front clamping bracket 6 and let go of the release button

5 again. Pay attention that the sanding sheet is clamped

centrally.

p Press the sanding sheet clamp 3 inward and pivot it to

the stop.

q Fold the sanding sheet 4 firmly around the sanding plate.

Guide the other end of the sanding sheet 4 between the

rear clamping bracket and the red roller on the clamping

bracket 3.

r Hold the sanding sheet tensely and press the clamping

bracket 3 toward the sanding plate to lock the sanding

sheet.

Sanding sheets without holes, e. g. from rolls or by the meter,

can be punctured with the perforating tool 14. For this, push

the power tool with the sanding sheet mounted onto the per-

forating tool (see figure F).

To remove the sanding sheet 4, loosen the clamping

bracket 3 and pull out the sanding sheet from the rear holding

fixture. Press the release button 5 and completely remove the

sanding sheet.

Selecting the Sanding Sheet

Depending on the material to be worked and the required rate

of material removal, different sanding sheets are available:

Dust/Chip Extraction

f Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suita-

ble for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

f Prevent dust accumulation at the workplace. Dusts can

easily ignite.

Integrated Dust Extraction with Dust Box

(see figures D1– D4)

Attach the dust box 1 onto the extraction outlet 9 until it latch-

es.

To empty the dust box 1, press the latching levers 10 on the

side of the dust box (n). Pull off the dust box toward the bot-

tom (o).

Before opening the dust box 1, it is recommended to loosen

the dust from the filter element by gently striking it against a

firm support (as shown in the figure).

Grasp the dust box 1 by the recessed grip, fold the filter ele-

ment 11 upward and empty the dust box. Clean the thin

plates of the filter element 11 with a soft brush.

External Dust Extraction (see figure E)

Slide the extraction adapter 12 onto the outlet piece 9. En-

sure that the latching levers of the extraction adapter engage.

The extraction adapter 12 accepts a vacuum hose with a di-

ameter of 19 mm.

An overview for connecting to different vacuum cleaners can

be found at the end of these operating instructions.

For removal of the extraction adapter 12, press the latching

levers together at the rear and pull the extraction adapter off.

The vacuum cleaner must be suitable for the material being

worked.

When vacuuming dry dust that is especially detrimental to

health or carcinogenic, use a special vacuum cleaner.

Operation

Starting Operation

f Observe correct mains voltage! The voltage of the pow-

er source must agree with the voltage specified on the

nameplate of the machine. Power tools marked with

230 V can also be operated with 220 V.

Switching On and Off

To start the machine, tilt the On/Off switch 7 toward the right

to the “I” position.

To switch off the machine, tilt the On/Off switch 7 toward the

left to the “0” position.

Grain size

For the working of all wooden ma-

terials

40—240

For coarse-sanding, e. g. of rough,

unplaned beams and boards coarse 40, 60

For face sanding and planing small ir-

regularities medium 80, 120

For finish and fine sanding of hard

woods fine 180, 240

For the working of paint/enamel

coats or primers and fillers

40—240

For sanding off paint coarse 40, 60

For sanding primer medium 80, 120

For final sanding of primers before

coating fine 180, 240

OBJ_DOKU-26314-001.fm Page 13 Monday, April 11, 2011 9:47 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GSS 140 A Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info