592632
17
Zoom out
Zoom in
Vorherige Seite
1/189
Nächste Seite
English | 17
Bosch Power Tools 2 609 140 479 | (22.1.08)
Sanding Sheets without Velcro Backing
(see figures CE)
n Press the release button 8 and keep it de-
pressed.
o Guide the sanding sheet 7 to the stop under
the opened front clamping bracket 9 and let
go of the release button 8 again. Pay atten-
tion that the sanding sheet is clamped cen-
trally.
p Press the release lever 5 and keep it de-
pressed.
q Place the sanding sheet 7 firmly around the
sanding plate. Guide the other end of the
sanding sheet 7 under the opened rear
clamping bracket 4.
r Hold the sanding sheet and let go of the re-
lease lever 5 to lock the sanding sheet.
Sanding sheets without holes, e. g. from rolls or
by the meter, can be punctured with the perfo-
rating tool 13. For this, push the power tool with
the sanding sheet mounted onto the perforating
tool (see figure F).
To remove the sanding sheet 7, press the re-
lease lever 5 and pull the sanding sheet out of
the rear clamping bracket. Push the release but-
ton 8 and remove the sanding sheet completely.
Selecting the Sanding Sheet
Depending on the material to be worked and the
required rate of material removal, different
sanding sheets are available:
Replacing the Sanding Plate
(see figure G)
The sanding plate 6 can be replaced, if required.
Unscrew the 4 screws 14 completely and re-
move the sanding plate 6. Attach the new sand-
ing plate 6 and tighten the screws again.
Operation
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V
can also be operated with 220 V.
Switching On and Off
To start the machine, press the On/Off switch 1
and keep it depressed.
To lock the pressed On/Off switch 1, press the
lock-on button 2.
To switch off the machine, release the On/Off
switch 1 or when it is locked with the lock-on
button 2, briefly press the On/Off switch 1 and
then release it.
Grain size
For the working of all
wooden materials
40
240
For coarse-sanding, e. g.
of rough, unplaned
beams and boards coarse 40, 60
For face sanding and plan-
ing small irregularities medium
80, 100,
120
For finish and fine sand-
ing of hard woods fine 180, 240
For the working of
paint/enamel coats or
primers and fillers
40
320
For sanding off paint coarse 40, 60
For sanding primer
medium
80, 100,
120
For final sanding of prim-
ers before coating fine
180,
240, 320
Grain size
OBJ_BUCH-384-001.book Page 17 Tuesday, January 22, 2008 8:26 AM
17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch GSS 23 A Professional wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info