Bedienungsanleitung Bosch GSS 23 AE Professional (Seite 19 von 97) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

592633

Zoom out

Zoom in

Vorherige Seite

1/97

Nächste Seite

English | 19

Bosch Power Tools 1 609 929 N27 | (11.12.07)

Replacing the Sanding Plate

(see figure F)

The sanding plate 6 can be replaced, if required.

Unscrew the 4 screws 11 completely and remove

the sanding plate 6. Attach the new sanding plate

6 and tighten the screws again.

Operation

Starting Operation

f Observe correct mains voltage! The voltage

of the power source must agree with the

voltage specified on the nameplate of the

machine. Power tools marked with 230 V can

also be operated with 220 V.

Switching On and Off

To start the machine, press the On/Off switch 2

and keep it depressed.

To lock the pressed On/Off switch 2, press the

lock-on button 3.

To switch off the machine, release the On/Off

switch 2 or when it is locked with the lock-on but-

ton 3, briefly press the On/Off switch 2 and then

release it.

Preselecting the Orbital Stroke Rate

With the thumbwheel for preselection of the or-

bital stroke rate 1, you can preselect the required

orbital stroke rate, even during operation.

The required stroke rate depends on the material

and the working conditions and can be deter-

mined through practical testing.

Working Advice

f Wait until the machine has come to a stand-

still before placing it down.

The removal capacity during sanding is mainly de-

termined by the selection of the sanding sheet as

well as the preselected orbital stroke rate.

Only flawless sanding sheets achieve good sand-

ing capacity and extend the service life of the ma-

chine.

Pay attention to apply uniform sanding pressure;

this increases the working life of the sanding

sheets.

Intensifiying the sanding pressure does not lead

to an increase of the sanding capacity, but to in-

creased wear of the machine and the sanding

sheet.

A sanding sheet that has been used for metal

should not be used for other materials.

Use only original Bosch sanding accessories.

Maintenance and Service

Maintenance and Cleaning

f Before any work on the machine itself, pull

the mains plug.

f For safe and proper working, always keep

the machine and ventilation slots clean.

If the machine should fail despite the care taken

in manufacturing and testing procedures, repair

should be carried out by an after-sales service

centre for Bosch power tools.

In all correspondence and spare parts order,

please always include the 10-digit article number

given on the type plate of the machine.

WARNING! Important instructions for connect-

ing a new 3-pin plug to the 2-wire cable.

The wires in the cable are coloured according to

the following code:

Do not connect the blue or brown wire to the

earth terminal of the plug.

Important: If for any reason the moulded plug is

removed from the cable of this power tool, it

must be disposed of safely.

OBJ_BUCH-80-002.book Page 19 Tuesday, December 11, 2007 8:02 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GSS 23 AE Professional Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch GSS 23 AE Professional

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info