Bedienungsanleitung Bosch GSS 23 AE (Seite 18 von 97) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

79000

Zoom out

Zoom in

Vorherige Seite

1/97

Nächste Seite

1 609 929 N27 | (11.12.07) Bosch Power Tools

18 | English

The vacuum cleaner must be suitable for the ma-

terial being worked.

When vacuuming dry dust that is especially detri-

mental to health or carcinogenic, use a special

vacuum cleaner.

Replacing the Sanding Sheet

When attaching a new sanding sheet, remove any

dust or debris from the sanding plate 6 (e. g. with

a brush).

To ensure optimum dust extraction, pay atten-

tion that the punched holes in the sanding sheet

match with the holes in the sanding plate.

Sanding Sheets with Velcro Backing

(see figure A)

The sanding plate 6 is fitted with Velcro backing

for quick and easy fastening of sanding sheets

with Velcro adhesion.

Before attaching the sanding sheet 7, free the

Velcro backing of the sanding plate 6 from any

debris by tapping against it in order to enable op-

timum adhesion.

Position the sanding sheet 7 flush alongside one

edge of the sanding plate 6, then lay the sanding

sheet onto the sanding plate and press it against

it with a light turning motion in clockwise direc-

tion.

To remove the sanding sheet 7, grasp it at one of

the tips and pull it off from the sanding plate 6.

Sanding Sheets without Velcro Backing

(see figures B–D)

n Press the release button 8 and keep it de-

pressed.

o Guide the sanding sheet 7 to the stop under

the opened front clamping bracket 9 and let

go of the release button 8 again. Pay atten-

tion that the sanding sheet is clamped cen-

trally.

p Press the sanding sheet clamp 5 inward and

pivot it to the stop.

q Fold the sanding sheet 7 firmly around the

sanding plate. Guide the other end of the

sanding sheet 7 between the rear clamping

bracket and the red roller on the clamping

bracket 5.

r Hold the sanding sheet tensely and press the

clamping bracket 5 toward the sanding plate

to lock the sanding sheet.

Sanding sheets without holes, e. g. from rolls or

by the meter, can be punctured with the perfo-

rating tool 10 for use with dust extraction. For

this, press the machine with the mounted sand-

ing sheet onto the perforating tool (see figure E).

To remove the sanding sheet 7, loosen the

clamping bracket 5 and pull out the sanding

sheet from the rear holding fixture. Press the re-

lease button 8 and completely remove the sand-

ing sheet.

Selecting the Sanding Sheet

Depending on the material to be worked and the

required rate of material removal, different sand-

ing sheets are available:

Grain size

For the working of

all wooden materials

40—240

For coarse-sanding,

e. g. of rough, un-

planed beams and

boards coarse 40, 60

For face sanding and

planing small irregu-

larities medium 80, 100, 120

For finish and fine

sanding of hard

woods fine 180, 240

For the working of

paint/enamel coats

or primers and fillers

—320

For sanding off paint coarse 40, 60

For sanding primer medium 80, 100, 120

For final sanding of

primers before coat-

ing fine 180, 240, 320

OBJ_BUCH-80-002.book Page 18 Tuesday, December 11, 2007 8:02 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GSS 23 AE Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info