Bedienungsanleitung Bosch gss 230 a (Seite 20 von 254) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

390110

Zoom out

Zoom in

Vorherige Seite

1/254

Nächste Seite

20 | English

2 609 932 790 | (6.12.10) Bosch Power Tools

Specialty Sanding Plates

You can replace the supplied sanding plate 9

with a specialty sanding plate, which is available

as an accessory.

The specialty sanding plate is attached in the

same manner as the one supplied.

Attach and remove the respective sanding

sheets in the same manner as when changing

original sanding sheets.

Extended Sanding Plate, Rectangular, Thin

(GSS 230 A/GSS 230 AE) (see figure G)

Use of the rectangular, thin, extended sanding

plate 22 enables sanding at hard-to-reach loca-

tions and narrow interspaces, e. g. on window

and door sills, grooves or behind radiators or

water pipes.

To mount the rectangular, thin, extended sand-

ing plate 22, use the corresponding screws 24.

Extended Sanding Plate, Triangular

(GSS 230 A/GSS 230 AE) (see figure H)

Use of the extended triangular sanding plate 26

enables sanding in edges and corners.

Finish-sanding Plate (without velcro backing)

(GSS 230 AE/GSS 280 AE) (see figure D)

When operating mainly with standard sanding

sheets without velcro backing, it is recommend-

ed to use the finish-sanding plate without velcro

backing. Due to its plane sanding plate surface,

optimum results are achieved, especially for fin-

ish sanding.

Auxiliary Handle

The auxiliary handle 1 enables convenient han-

dling and optimal distribution of power, espe-

cially at high removal rates.

Fasten the auxiliary handle 1 with screw 2 to the

casing.

Operation

Starting Operation

f Observe correct mains voltage! The voltage

of the power source must agree with the

voltage specified on the nameplate of the

machine. Power tools marked with 230 V

can also be operated with 220 V.

Switching On and Off

To start the machine, press the On/Off switch 4

and keep it pressed.

To lock the pressed On/Off switch 4, press the

lock-on button 5.

To switch off the machine, release the On/Off

switch 4 or when it is locked with the lock-on

button 5, briefly press the On/Off switch 4 and

then release it.

Preselecting the Orbital Stroke Rate

(GSS 230 AE/GSS 280 AE)

With the thumbwheel for preselection of the or-

bital stroke rate 3, you can preselect the re-

quired orbital stroke rate, even during opera-

tion.

The required stroke rate depends on the materi-

al and the working conditions and can be deter-

mined through practical testing.

Working Advice

f Wait until the machine has come to a stand-

still before placing it down.

The removal capacity during sanding is mainly

determined by the selection of the sanding

sheet as well as the preselected orbital stroke

rate (GSS 230 AE/GSS 280 AE).

Only flawless sanding sheets achieve good

sanding capacity and extend the service life of

the machine.

Pay attention to apply uniform sanding pres-

sure; this increases the working life of the sand-

ing sheets.

Intensifiying the sanding pressure does not lead

to an increase of the sanding capacity, but to in-

creased wear of the machine and the sanding

sheet.

OBJ_BUCH-426-004.book Page 20 Monday, December 6, 2010 8:24 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch gss 230 a Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info