Bedienungsanleitung Bosch GSS 280 A (Seite 19 von 254) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

78207

Zoom out

Zoom in

Vorherige Seite

1/254

Nächste Seite

English | 19

Bosch Power Tools 2 609 932 790 | (6.12.10)

When vacuuming dry dust that is especially det-

rimental to health or carcinogenic, use a special

vacuum cleaner.

Replacing the Sanding Sheet

When attaching a new sanding sheet, remove

any dust or debris from the sanding plate 9 (e. g.

with a brush).

To ensure optimum dust extraction, pay atten-

tion that the punched holes in the sanding sheet

match with the holes in the sanding plate.

Sanding Sheets with Velcro Backing

(see figure C)

The sanding plate 9 is fitted with Velcro backing

for quick and easy fastening of sanding sheets

with Velcro adhesion.

Before attaching the sanding sheet 19, free the

Velcro backing of the sanding plate 9 from any

debris by tapping against it in order to enable

optimum adhesion.

Position the sanding sheet 19 flush alongside

one edge of the sanding plate 9, then lay the

sanding sheet onto the sanding plate and press

firmly.

To remove the sanding sheet 19, grasp it at one

of the tips and pull it off from the sanding plate

Sanding Sheets without Velcro Backing

(see figure D)

Lightly lift and unlatch the sanding-sheet clamp

Guide the sanding sheet 19 under the opened

rear clamping bracket 10 to the stop and clamp

the sanding sheet by reinserting the sanding-

sheet clamp 8.

Fold the sanding sheet 19 firmly around the

sanding plate. Guide the other end of the sand-

ing sheet 19 under the open front clamping

bracket 10 and clamp the sanding sheet by rein-

serting the sanding-sheet clamp 8.

Sanding sheets without holes, e. g. from rolls or

by the meter, can be punctured with the perfo-

rating tool 20 for use with dust extraction. For

this, press the machine with the mounted sand-

ing sheet onto the perforating tool

(see figure E).

To remove the sanding sheet 19, unlatch the

sanding-sheet clamp 8 and pull out the sanding

sheet.

Selecting the Sanding Sheet

Depending on the material to be worked and the

required rate of material removal, different

sanding sheets are available:

Replacing the Sanding Plate

(see figure F)

The sanding plate 9 can be replaced, if required.

Unscrew the 6 screws 21 completely and re-

move the sanding plate 9. Attach the new sand-

ing plate 9 and tighten the screws again.

Grain size

For the working of all

wooden materials

40—240

For coarse-sanding, e. g.

of rough, unplaned

beams and boards

coarse 40, 60

For face sanding and

planing small irregulari-

ties

medium 80, 100,

120

For finish and fine sand-

ing of hard woods

fine 180, 240

For the working of

paint/enamel coats or

primers and fillers

40—320

For sanding off paint coarse 40, 60

For sanding primer medium 80, 100,

120

For final sanding of prim-

ers before coating

fine 180,

240, 320

OBJ_BUCH-426-004.book Page 19 Monday, December 6, 2010 8:24 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GSS 280 A Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info