Bedienungsanleitung Bosch GST 12V-70 Professional (Seite 18 von 259) (Alle Sprachen)

786101

Zoom out

Zoom in

Vorherige Seite

1/259

Nächste Seite

18 | English

Certain dusts, such as oak or beech dust, are classified as

carcinogenic, especially in conjunction with wood treatment

additives (chromate, wood preservative). Materials contain-

ing asbestos may only be machined by specialists.

– Use a dust extraction system that is suitable for the ma-

terial wherever possible.

– Provide good ventilation at the workplace.

– It is advisable to wear a P2 filter class breathing mask.

The regulations on the material being machined that apply in

the country of use must be observed.

uAvoid dust accumulation at the workplace. Dust can

easily ignite.

Hood

Fit the hood (15) before you connect the power tool to the

dust extraction system.

Attach the hood(15) to the power tool so that the bracket

locks into place on the shock protection guard(21).

Remove the hood(15) when working without a dust extrac-

tion system and for mitre/bevel cuts. To do this, pull the

hood forwards off the shock protection guard(21).

Connecting the dust extraction (see figures F–G)

Fit the extraction outlet(16) in the recesses of the base

plate(9).

Connect a dust extraction hose (22) (accessory) to the ex-

traction outlet (16). Connect the dust extraction hose (22)

to a dust extractor (accessory).

You will find an overview of connecting to various dust ex-

tractors at the end of these operating instructions.

For optimum dust extraction, where possible use the anti-

splinter guard (18).

The dust extractor must be suitable for the material being

worked.

When extracting dry dust that is especially detrimental to

health or carcinogenic, use a special dust extractor.

Operation

Operating modes

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Pendulum action settings

The pendulum action can be adjusted using three different

settings, allowing the cutting speed, cutting capacity and the

cut itself to be optimally adapted to the material that you

want to cut.

You can also adjust the pendulum action during operation

using the adjusting lever (8).

Level0 No pendulum action

LevelLow pendulum action

LevelHigh pendulum action

The optimum pendulum level for each application can be de-

termined by a practical test. Note the following recommend-

ations:

– Select a lower pendulum level or switch off the pendulum

action completely if you wish to produce a finer or cleaner

cutting edge.

– Switch off the pendulum action when machining thin ma-

terials (e.g. sheets).

– Work on hard materials (e.g. steel) with low pendulum ac-

tion.

– You can work on soft materials and saw wood using max-

imum pendulum action.

Adjusting the mitre/bevel angle (see figureH)

The base plate (9) can be swivelled to the right or left to

make mitre cuts up to 45°.

The extraction outlet (16) and anti-splinter guard (18) can-

not be used while mitre/bevel cuts are being made.

– Remove the extraction outlet(16) and the anti-splinter

guard(18).

– For mitre/bevel angle 0°, there is a pin in a corresponding

recess.

– Loosen the screw(23) with the hex key(24) until you can

slide the base plate(9) in towards the battery(1). Let the

pin slide into the guide groove.

– To adjust mitre/bevel angles, swivel the base plate(9) to

the required position according to the scale(25). Every

angle can be adjusted to 45° using a protractor.

– Retighten the screw(23).

Starting Operation

Inserting the battery

Note: The use of batteries unsuitable for your power tool can

lead to malfunctions or damage to the power tool.

Insert the charged battery(1) into the battery receptacle un-

til you feel it engage and it is securely locked in place.

Switching on the LED worklight

To switch the worklight(14) on or off, press the worklight

button(3).

uDo not look directly into the worklight; it can blind

you.

Switching on/off

uMake sure that you are able to press the On/Off switch

without releasing the handle.

To switch on the power tool, slide the on/off switch(7) for-

wards so that "I" appears on the switch.

To switch off the power tool, slide the on/off switch(7)

backwards so that "0" appears on the switch.

Restart protection

The restart protection feature prevents the power tool from

uncontrolled starting after the power supply to it has been

interrupted. Once the restart protection is active, the tem-

perature monitoring/overload protection indicator(6)

flashes continuously.

1 609 92A 85Y | (15.07.2022) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GST 12V-70 Professional Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info