Bedienungsanleitung Bosch GTA 3800 (Seite 16 von 125) (Alle Sprachen)

786483

Zoom out

Zoom in

Vorherige Seite

1/125

Nächste Seite

16 | English

Saw stand GTA 3800

Length of saw stand without

table extension mm 1578

Length of saw stand with table

extension mm 3877

Saw stand height mm 824

Max. load bearing capacity (power tool + workpiece)

without table extension

– Holder sets kg 250

Max. load bearing capacity (power tool + workpiece) with

table extension

– Holder sets kg 150

– Per table extension kg 50

Weight according to EPTA-Pro-

cedure01:2014 kg 22.4

Assembly

Items included

See the list of items included at the start of the

operating manual.

Check to ensure that all the parts listed below have been

supplied before assembling the saw stand:

No. Designation Quantity

GTA 3800 saw stand 1

(4) Holder set 2

(1) Workpiece support 2

(7) Roller support 2

(14) Socket spanner (13mm)/hex key

(4mm)/cross-headed screwdriver 1

(19) Power tool fastening set consists of:

– Hexagon screw (M8 x 45) 4

– Washer 4

Extra tools required (not included in the delivery):

– Open-end spanner (10mm)

Installing the Saw Stand

Carefully remove all parts included in the delivery from their

packaging.

Remove all packing material.

Setting up the saw stand (see figures A1−A2)

– Place the saw stand on the floor with legs up.

– Press the locking pin(15) in and swivel the leg up until

the locking pin audibly engages again.

– Repeat this work step with the other three legs.

– Rotate the saw stand into the working position.

– Make sure that the saw stand is stable and all locking pins

have engaged.

– A height-adjustable foot(9) helps you to align the saw

stand.

– Screw the foot in or out until the saw stand is level and all

four legs are on the ground.

Installing roller support (see figure B1)

– Unscrew the cross-head screw of the roller support(7)

with the supplied cross-headed screwdriver(14).

If required, resist the lock nut on the other side of the

roller support with an open-end spanner (10mm).

– Remove the roller support(7).

There are various options as to how the individual rollers can

be arranged on the workpiece support using the internal

threaded rod.

– Arrange the individual parts as required and push the in-

ternal threaded rod through the rollers and through the

workpiece support(1).

– Screw all parts back together.

Installing workpiece support (see figure B2)

– Release the locking knobs(3) and pull the table

extensions(2) slightly out on both sides of the saw stand.

– Push the workpiece supports(1) from left and right re-

spectively into the upper groove of the saw stand or the

table extension.

– The length stops(8) must point outwards here.

– Pull the locking knob(6) to lock the workpiece support.

Preparing the Saw Stand

Preparing holder sets (seefiguresC1–C4)

– To unlock the holder sets(4), press the buttons(16) and

open the levers(17) respectively.

– Measure the distance x between the assembly holes on

your power tool.

– Position the holder sets(4) in the centre of the saw stand

and at the appropriate distance x from each other.

– Close each lever(17) again. This allows the holder sets to

be firmly positioned on the saw stand.

Setting up the saw stand (seefigureD)

– Bring the power tool into the transport position. Informa-

tion about the transport position can be found in the op-

erating instructions for the corresponding power tool.

– Position the movable nuts(18) in the holder sets so that

they match the assembly holes on the power tool.

– Screw using the supplied socket spanner(14) holder set

and power tool with the hexagon screws and washers

from the fastening set(19).

Operation

Working Advice

Always hold the workpiece firmly in place, especially long,

heavy pieces. Once the workpiece has been cut, the centre

of gravity may be displaced, causing the saw stand to tip

over.

1 609 92A 6JA | (06.09.2021) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GTA 3800 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info