Bedienungsanleitung Bosch GTK 40 Professional (Seite 14 von 160) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

594785

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

1 609 92A 10X | (11.11.14) Bosch Power Tools

14 | English

 Do not use this to pneumatic tool to fasten electrical

wiring. It is not suitable for fastening electrical wiring,

can damage the insulation of electric cables and thus

lead to electric shock and danger of fire.

 Never use oxygen or flammable gases as the energy

source for the pneumatic tool. Flammable gases are

dangerous and can cause the pneumatic tool to ex-

plode.

 Use appropriate detectors to determine if utility

lines are hidden in the work area or call the local util-

ity company for assistance. Contact with electric lines

can lead to fire and electric shock. Damaging a gas line

can lead to explosion. Penetrating a water line causes

property damage.

 The pneumatic tool may only be connected to lines,

for which the maximal permissible pressure of the

pneumatic tool cannot be exceeded by more than

10 %; for higher pressures, a pressure control valve

(pressure reducer) with preceding pressure-limita-

tion valve in the compressed-air line must be in-

stalled. Excessive pressure leads to abnormal opera-

tion or breakage of the pneumatic tool, which can lead

to injury.

Product Description and Specifica-

tions

Read all safety warnings and all instruc-

tions. Failure to follow the warnings and in-

structions may result in electric shock, fire

and/or serious injury.

Intended Use

The pneumatic tool is intended for connecting work in roof-

ing, encasing, battening, manufacturing wall and ceiling el-

ements, wood facades, pallets, wood fences, noise-reduc-

tion walls and boxes.

Only the fasteners (nails, staples, etc.) specified in table

“Technical Data” may be used.

Product Features

The numbering of the product features refers to the illus-

tration of the pneumatic tool on the graphics page.

1 Workpiece protector

2 Discharge lock-off

3 Thumbwheel for depth stop adjustment

4 Air outlet with adjustable exhaust cap

5 Handle

6 Air connector

7 Magazine-slider lock (GTK 40)

8 Magazine

9 Selector switch for actuation system

10 Trigger

11 Magazine slider (GTK 40)

12 Clamping lever for opening/closing the shot duct

(GTK 40)

13 Outlet

14 Magazine lock (GSK 50)

15 Refill indicator (GSK 50)

16 Air-connection coupling

17 Supply-air hose

18 Staple strip*

19 Nail strip*

20 Magazine rail (GSK 50)

21 Driver blade

22 Storage for workpiece protector

*Accessories shown or described are not part of the standard

delivery scope of the product. A complete overview of accesso-

ries can be found in our accessories program.

Technical Data

Noise/Vibration Information

Sound emission values determined according to

EN 12549.

Typically the A-weighted noise levels of the pneumatic tool

are: Sound pressure level 96 dB(A); sound power level

110 dB(A). Uncertainty K=3 dB.

Wear hearing protection!

Vibration total values a

and uncertainty K determined ac-

cording to EN ISO 20643: a

<2.5m/s

, K= 1.5 m/s

Declaration of Conformity

We declare under our sole responsibility that the product

described under “Technical data” complies with all applica-

ble provisions of the directive 2006/42/EC including its

amendments and is in conformity with the following stand-

ards: EN 792-13.

Technical file (2006/42/EC) at:

Robert Bosch GmbH, PT/ETM9,

70764 Leinfelden-Echterdingen, GERMANY

Robert Bosch GmbH, Power Tools Division

70764 Leinfelden-Echterdingen, GERMANY

Leinfelden, 13.11.2014

Assembly

Connecting the Air Supply (see figure A)

Make sure that the pressure of the compressed-air system

is below the maximum permitted rated pressure of the

pneumatic tool. Firstly, set the air pressure to the lower

value of the recommended rated pressure (see “Technical

Data”).

When in doubt, check the pressure at the air inlet with a

pressure gauge with the pneumatic tool switched on.

For maximum performance, the values for the supply-air

hose 17 (connection thread, maximum operating pres-

sure, inner hose diameter, maximum hose length; see

“Technical Data”) must be observed.

The compressed air supplied should be free of foreign ma-

terial and moisture to protect the tool from damage, con-

tamination, and the formation of rust.

All fittings, connecting lines and hoses must be dimen-

sioned for the pressure and the required air volume.

Avoid restrictions in the air supply, e.g., from pinching,

kinking, or stretching!

Compressed-air nailer GTK 40 GSK 50

Article number

3 601 D91 G.. 3601D91D..

Driving force at 6.3 bar (91 psi)

Nm 18.4 17.8

Actuation systems

– Single actuation with safety run

– Contact actuation



Fastener

–Type

–Length

–Diameter

Staple strip

13–40

1,2

Nail strip

Brads

15, 19, 25, 30, 35, 40, 45, 50

1,2

Magazine capacity, max.

100 100

Engine oil SAE 10, SAE 20

ml 0.25–0.5 0.25–0.5

Internal volume

ml 196.5 200

Max. working pressure

bar 5–8 5–8

Connecting thread

"¼¼

Supply-air hose

– Max. operating pressure at 20 °C

– Inner diameter of hose

– Max. hose length

bar

Air consumption per driving procedure at 6.8 bar (100 psi)

l0.710.69

Dimensions

–Height

–Width

–Length

246

272

251

260

Weight according to EPTA-Procedure 01/2003

kg 1.14 1.14

Henk Becker

Executive Vice President

Engineering

Helmut Heinzelmann

Head of Product Certification

PT/ETM9

OBJ_BUCH-1038-004.book Page 14 Tuesday, November 11, 2014 2:36 PM

Bosch GTK 40 Professional Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info