Bedienungsanleitung Bosch gwb 7 2 (Seite 16 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

386231

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

1 609 929 M57 | (12.9.07) Bosch Power Tools

16 | English

An estimation of the level of exposure to vibra-

tion should also take into account the times

when the tool is switched off or when it is run-

ning but not actually doing the job. This may sig-

nificantly reduce the exposure level over the total

working period.

Identify additional safety measures to protect the

operator from the effects of vibration such as:

maintain the tool and the accessories, keep the

hands warm, organisation of work patterns.

Assembly

Battery Charging

A battery that is new or has not been used for a

longer period does not develop its full capacity

until after approx. 5 charging/discharging cycles.

To remove the battery 1, press the unlocking but-

tons and pull the battery out of the machine to

the rear. Do not exert any force.

The battery is equipped with a NTC temperature

control which allows charging only within a tem-

perature range of between 0 °C and 45 °C. A long

battery service life is achieved in this manner.

A significantly reduced working period after

charging indicates that the battery is used and

must be replaced.

Observe the notes for disposal.

Changing the Tool

f Before any work on the machine (e. g., main-

tenance, tool change, etc.) as well as during

transport and storage, set the rotational di-

rection switch to the centre position. Unin-

tentional actuation of the On/Off switch can

lead to injuries.

Open the key type drill chuck 8 by turning until

the tool can be inserted. Insert the tool.

Insert the chuck key 6 into the corresponding

holes of the key type drill chuck 8 and clamp the

tool uniformly.

Screwdriver Tools

When working with screwdriver bits 5, a univer-

sal bit holder should always be used. Use only

screwdriver bits that fit the screw head.

Replacing the Drill Chuck

f Before any work on the machine (e. g., main-

tenance, tool change, etc.) as well as during

transport and storage, set the rotational di-

rection switch to the centre position. Unin-

tentional actuation of the On/Off switch can

lead to injuries.

Removing the Securing Screw

The key type drill chuck 8 is secured with a secur-

ing screw 7 against unintentional loosening.

Open the drill chuck 8 completely and unscrew

the securing screw 7 by turning in clockwise di-

rection. Please observe that the securing screw

has a left-hand thread.

Removing the Drill Chuck

To remove the key type drill chuck 8, clamp an Al-

len key into the key type drill chuck 8. Place the

machine onto a stable support, e. g. a work-

bench. Hold the machine tightly and loosen the

key type drill chuck 8 by turning the Allen key in

anticlockwise direction. A tightly seated key type

drill chuck is loosened by applying a light blow

onto the long end of the Allen key . Remove the

Allen key from the key type drill chuck and fully

unscrew the drill chuck.

Mounting the Drill Chuck

The key type drill chuck is mounted in reverse or-

der.

Note: After mounting the key type drill chuck,

screw the securing screw 7 in again.

The drill chuck must be tightened with a

tightening torque of approx. 10–20 Nm.

OBJ_BUCH-498-001.book Page 16 Wednesday, September 12, 2007 3:55 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch gwb 7 2 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info