Bedienungsanleitung Bosch GWS 10-125 (Seite 34 von 199) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

78611

Zoom out

Zoom in

Vorherige Seite

1/199

Nächste Seite

English | 35

Bosch Power Tools 1 609 929 L00 | (25.7.08)

Cutting Metal

f For cutting metal, always work with the pro-

tection guard for cutting 13.

When cutting, work with moderate feed, adapt-

ed to the material being cut. Do not exert pres-

sure onto the cutting disc, tilt or oscillate the

machine.

Do not reduce the speed of running down cut-

ting discs by applying sideward pressure.

The machine must

always work in an

up-grinding mo-

tion. Otherwise,

the danger exists

of it being pushed

uncontrolled out

of the cut.

When cutting pro-

files and square

bar, it is best to

start at the small-

est cross section.

Cutting Stone

f For cutting stone, always work with the cut-

ting guide with dust extraction protection

guard 20.

f The machine may be used only for dry cut-

ting/grinding.

For cutting stone, it is best to use a diamond

cutting disc. As a safety measure against jam-

ming, the cutting guide with dust extraction pro-

tection guard 20 must be used.

Operate the machine only with dust extraction

and additionally wear a dust protection mask.

The vacuum cleaner must be approved for the

extraction of masonry dust. Bosch provides suit-

able vacuum cleaners.

Switch on the ma-

chine and place

the front part of

the cutting guide

on the workpiece.

Slide the machine

with moderate

feed, adapted to

the material to be

worked.

For cutting expecially hard material, e. g., con-

crete with high pebble content, the diamond

cutting disc can overheat and become damaged

as a result. This is clearly indicated by circular

sparking, rotating with the diamond cutting

disc.

In this case, interrupt the cutting process and al-

low the diamond cutting disc to cool by running

the machine for a short time at maximum speed

with no load.

Noticeable decreasing work progress and circu-

lar sparking are indications of a diamond cutting

disc that has become dull. Briefly cutting into

abrasive material (e. g. lime-sand brick) can re-

sharpen the disc again.

Information on Structures

Slots in structural walls are subject to the

Standard DIN 1053 Part 1, or country-specific

regulations.

These regulations are to be observed under all

circumstances. Before beginning work, consult

the responsible structural engineer, architect or

the construction supervisor.

Maintenance and Service

Maintenance and Cleaning

f Before any work on the machine itself, pull

the mains plug.

f For safe and proper working, always keep

the machine and ventilation slots clean.

f In extreme working conditions, conductive

dust can accumulate in the interior of the

machine when working with metal. The pro-

tective insulation of the machine can be de-

graded. The use of a stationary extraction

system is recommended in such cases as

well as frequently blowing out the ventila-

tion slots and installing a residual current

device (RCD).

OBJ_BUCH-340-002.book Page 35 Friday, July 25, 2008 9:21 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GWS 10-125 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info