Bedienungsanleitung Bosch GWS 11-125 P (Seite 24 von 395) (Alle Sprachen)

786323

Zoom out

Zoom in

Vorherige Seite

1/395

Nächste Seite

24 | English

GWS 11-125 P GWS 11-125 P GWS 15-125 CIEP

m/s2

6.0

1.5

6.0

1.5

6.0

1.5

Disc sanding:

m/s2

3.0

1.5

3.0

1.5

3.0

1.5

Grinding thin metal sheets or other materials that tend to easily vibrate with a large surface area can cause the noise emission

value to increase by up to 15dB. Suitable, heavy damping mats can reduce the increased noise emissions. Increased noise

emissions must be taken into consideration, both for the risk assessment of the noise output and for selecting suitable hearing

protection.

The vibration level and noise emission value given in these

instructions have been measured in accordance with a

standardised measuring procedure and may be used to com-

pare power tools. They may also be used for a preliminary

estimation of vibration and noise emissions.

The stated vibration level and noise emission value repres-

ent the main applications of the power tool. However, if the

power tool is used for other applications, with different ap-

plication tools or is poorly maintained, the vibration level

and noise emission value may differ. This may significantly

increase the vibration and noise emissions over the total

working period.

To estimate vibration and noise emissions accurately, the

times when the tool is switched off or when it is running but

not actually being used should also be taken into account.

This may significantly reduce vibration and noise emissions

over the total working period.

Implement additional safety measures to protect the oper-

ator from the effects of vibration, such as servicing the

power tool and application tools, keeping their hands warm,

and organising workflows correctly.

Kickback stop

(GWS15-125CIEP)

If there is a sudden kickback in the power tool,

e.g. jamming in a separating cut, the power

supply to the motor will be interrupted elec-

tronically.

To restart the tool, set the On/Off switch (3) to the "off" po-

sition and then switch the power tool on again.

Restart protection

(GWS15-125CIEP)

The restart protection feature prevents the power tool from

uncontrolled starting after the power supply to it has been

interrupted.

To restart the tool, set the on/off switch (3) to the "off" posi-

tion and then switch the power tool on again.

Soft start

(GWS15-125CIEP)

The electronic soft start limits the torque when the power

tool is switched on and enables a smooth start-up.

Note: If the power tool runs at full speed immediately after

being switched on, this means that the soft start and restart

protection mechanisms have failed. The power tool must be

sent to the after-sales service immediately; see the "After-

Sales Service and Application Service" section for ad-

dresses.

Constant Electronic control

(GWS15-125CIEP)

The Constant Electronic keeps the speed at no load and un-

der load virtually consistent, guaranteeing uniform perform-

ance.

Speed preselection

(GWS 15-125 CIEP)

You can preselect the required speed using the speed preselection thumbwheel (4), even during operation. The information in

the table below describes the recommended values.

Material Application Application tool Thumbwheel position

Metal Removing paint Sanding sheet 2–3

Metal Brushing, removing rust Cup brush, abrasive disc 3

Stainless steel Grinding Grinding disc/fibre disc 4–6

Metal Rough grinding Grinding disc 6

Metal Cutting Cutting disc 6

Stone Cutting Diamond cutting disc 6

1 609 92A 7AL | (30.03.2022) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GWS 11-125 P Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info