Bedienungsanleitung Bosch GWS 14-150 CI (Seite 32 von 199) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

105995

Zoom out

Zoom in

Vorherige Seite

1/199

Nächste Seite

English | 33

Bosch Power Tools 1 609 929 L00 | (25.7.08)

Rotating the Machine Head

f Before any work on the machine itself, pull

the mains plug.

The machine head

can be rotated with

respect to the ma-

chine housing in

90° steps. In this

manner, the On/Off

switch can be

brought into a more

convenient posi-

tion for special

working situations,

e.g., for cutting op-

erations using the cutting guide with dust ex-

traction protection guard 20/cut off stand or for

left-handed persons.

Completely unscrew the four screws. Rotate the

machine head carefully, without removing it

from the housing, to the new position. Screw in

and tighten the four screws again.

Dust/Chip Extraction

f Dusts from materials such as lead-containing

coatings, some wood types, minerals and

metal can be harmful to one’s health. Touch-

ing or breathing-in the dusts can cause aller-

gic reactions and/or lead to respiratory infec-

tions of the user or bystanders.

Certain dusts, such as oak or beech dust, are

considered as carcinogenic, especially in

connection with wood-treatment additives

(chromate, wood preservative). Materials

containing asbestos may only be worked by

specialists.

– Use dust extraction whenever possible.

– Provide for good ventilation of the work-

ing place.

– It is recommended to wear a P2 filter-

class respirator.

Observe the relevant regulations in your

country for the materials to be worked.

Operation

Starting Operation

f Observe correct mains voltage! The voltage

of the power source must agree with the

voltage specified on the nameplate of the

machine. Power tools marked with 230 V

can also be operated with 220 V.

When operating the machine with power from

mobile generators that do not have sufficient re-

serve capacity or are not equipped with suitable

voltage control with starting current amplifica-

tion, loss of performance or untypical behavior

can occur upon switching on.

Please observe the suitability of the power gen-

erator being used, particularly with regard to

the mains voltage and frequency.

Switching On and Off

To start the power tool, push the On/Off switch

4 forwards.

To lock the On/Off switch 4, press the On/Off

switch 4 down at the front until it latches.

To switch off the power tool, release the On/Off

switch 4 or, if it is locked, briefly push down the

back of the On/Off switch 4 and then release it.

f Check grinding tools before using. The

grinding tool must be mounted properly

and be able to move freely. Carry out a test

run for at least one minute with no load. Do

not use damaged, out-of-centre or vibrating

grinding tools. Damaged grinding tools can

burst and cause injuries.

Kickback stop

(GWS 11-125 CI/GWS 11-125 CIE/

GWS 14-125 CI/GWS 14-125 CIE/

GWS 14-125 CIT/GWS 14-150 CI)

In case of a sudden drop in speed,

e.g., caused by a jammed disc

while cutting, the power supply to

the motor is electronically inter-

rupted.

To restart the operation, switch the On/Off

switch 4 to the Off position and start the ma-

chine again.

OBJ_BUCH-340-002.book Page 33 Friday, July 25, 2008 9:21 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GWS 14-150 CI Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch GWS 14-150 CI

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info