Bedienungsanleitung Bosch gws 1400 professional (Seite 22 von 301) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

391343

Zoom out

Zoom in

Vorherige Seite

1/301

Nächste Seite

English | 231 609 929 K94 • 20.12.06

Grinding/Cutting Disc

Pay attention to the dimensions of the grinding tools.

The mounting hole diameter must fit the mounting

flange without play. Do not use reducers or adapters.

When using diamond cutting discs, pay attention that

the direction-of-rotation arrow on the diamond cutting

disc and the direction of rotation of the machine (see

direction-of-rotation arrow on the machine head)

agree.

See graphics page for the mounting sequence.

To fasten the grinding/cutting disc, screw on the

clamping nut 9 and tighten with the two-pin spanner;

see Section “Quick-clamping Nut ”.

f After mounting the grinding tool and before

switching on, check that the grinding tool is

correctly mounted and that it can turn freely.

Make sure that the grinding tool does not

graze against the protection guard or other

parts.

An O-ring (plastic part) is inserted

in the mounting flange 7 around the

centring collar. If the O-ring is

missing or is damaged, it must

in all cases be replaced (article

number 1 600 210 039) before

the mounting flange 7 is mounted.

Flap Disc

f For operations with the rubber sanding plate

15 or with the cup brush/wheel brush/flap

disc, always mount the hand guard 14.

Place the special mounting flange (article number

2 605 703 028) and the flap disc on the grinder spin-

dle 5. Screw on the clamping nut 9 and tighten with

the two-pin spanner.

Rubber Sanding Plate

f For operations with the rubber sanding plate

15 or with the cup brush/wheel brush/flap

disc, always mount the hand guard 14.

See graphics page for the mounting sequence.

Screw on the round nut 17 and tighten with the two-

pin spanner.

Cup Brush/Disc Brush

f For operations with the rubber sanding plate

15 or with the cup brush/wheel brush/flap

disc, always mount the hand guard 14.

See graphics page for the mounting sequence.

The cup brush/disc brush must be able to be screwed

onto the grinder spindle until it rests firmly against the

grinder spindle flange at the end of the grinder spindle

threads. Tighten the cup brush/disc brush with an

open-end spanner.

Quick-clamping Nut

For convenient changing of grinding tools without the

use of additional tools, you can use the quick-clamp-

ing nut 10 instead of the clamping nut 9.

f The quick-clamping nut 10 may be used only

for grinding or cutting discs.

Use only a flawless, undamaged quick-clamp-

ing nut 10.

When screwing on, pay attention that the side

of the quick-clamping nut 10 with printing does

not face the grinding disc; the arrow must point

to the index mark 21.

Lock the grinder spindle

with the spindle lock but-

ton 2. To tighten the quick-

clamping nut, firmly turn

the grinding disc in clock-

wise direction.

A properly attached,

undamaged quick-clamp-

ing nut can be loosened

by hand when turning the

knurled ring in anticlock-

wise direction.

Never loosen a tight

quick-clamping nut

with pliers. Always use

the two-pin spanner.

Insert the two-pin spanner

as shown in the illustra-

tion.

OBJ_BUCH-310-001.book Page 23 Wednesday, December 20, 2006 9:31 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch gws 1400 professional Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info