Bedienungsanleitung Bosch GWS 15-125 CI (Seite 14 von 270) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544248

Zoom out

Zoom in

Vorherige Seite

1/270

Nächste Seite

14 | English

1 609 92A 095 | (30.4.13) Bosch Power Tools

Additional Safety and Working

Instructions

 Observe the mains voltage! The voltage of the power

source must correspond with the data on the type plate

of the machine.

 Use suitable detectors to determine if utility lines are

hidden in the work area or call the local utility company

for assistance. Contact with electric lines can lead to fire

and electric shock. Damaging a gas line can lead to explo-

sion. Penetrating a water line causes property damage or

may cause an electric shock.

 Release the On/Off switch and set it to the off position

when the power supply is interrupted, e. g., in case of a

power failure or when the mains plug is pulled. This pre-

vents uncontrolled restarting.

 Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health and cause allergic reactions, lead to res-

piratory infections and/or cancer. Materials containing

asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suita-

ble for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

 Prevent dust accumulation at the workplace. Dusts can

easily ignite.

 Secure the workpiece. A workpiece clamped with clamp-

ing devices or in a vice is held more secure than by hand.

 After breakage of the grinding disc during operation or

damage to the holding fixtures on the protection

guard/power tool, the machine must promptly be sent to

an after-sales service agent for maintenance for address-

es, see section “After-sales Service and Application Ser-

vice”.

 Adjust protection guard in such a manner that sparking

toward the operator is prevented.

 The protection guard may only be turned while actuat-

ing the release lever on the gear head. Otherwise, the

machine may not continue to be used anymore and

must be sent to an after-sales service agent.

 Do not touch grinding and cutting discs before they

have cooled down. The discs can become very hot while

working.

 Actuate the spindle lock button only when the grinder

spindle is at a standstill. Otherwise, the machine may be-

come damaged.

 After mounting the grinding tool and before switching

on, check that the grinding tool is correctly mounted

and that it can turn freely. Make sure that the grinding

tool does not graze against the protection guard or oth-

er parts.

 When operating the machine with power from mobile gen-

erators, loss of performance or untypical behavior can oc-

cur upon switching on.

 By applying too high application force, the machine can

be subject to overload. Overload can lead to overheat-

ing and damage of the power tool. After heavily strain-

ing the power tool, continue to run it at no-load for sev-

eral minutes in order to cool it down.

 Do not use the power tool with a cut-off stand.

 Never use a cutting disc for roughing.

 The quick-clamping nut may be used only for grinding

or cutting discs. Use only a flawless, undamaged quick-

clamping nut.

 Do not pull out the gear head while turning it –

see figure 12, page 265.

 To save energy, only switch the power tool on when using it.

Products sold in GB only: Your product is fitted with an

BS 1363/A approved electric plug with internal fuse (ASTA

approved to BS 1362).

If the plug is not suitable for your socket outlets, it should be

cut off and an appropriate plug fitted in its place by an author-

ised customer service agent. The replacement plug should

have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible

shock hazard and should never be inserted into a mains sock-

et elsewhere.

Products sold in AUS and NZ only: Use a residual current de-

vice (RCD) with a rated residual current of 30 mA or less.

Symbols

The following symbols are important for reading and under-

standing the operating instructions. Please take note of the

symbols and their meaning. The correct interpretation of the

symbols will help you to use the machine in a better and safer

manner.

Symbol Meaning

Article number

Read all safety warnings and all instruc-

tions

Before any work on the machine itself,

pull the mains plug from the socket out-

let

Wear protective gloves

Always wear ear protection.

OBJ_BUCH-1425-004.book Page 14 Tuesday, April 30, 2013 2:19 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GWS 15-125 CI Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info