Bedienungsanleitung Bosch GWS 17-150 S (Seite 23 von 437) (Alle Sprachen)

786319

Zoom out

Zoom in

Vorherige Seite

1/437

Nächste Seite

English | 23

back may propel the spinning wheel and the power tool

directly at you.

uWhen the wheel is binding or when interrupting a cut

for any reason, switch off the power tool and hold it

motionless until the wheel comes to a complete stop.

Never attempt to remove the cut-off wheel from the

cut while the wheel is in motion otherwise kickback

may occur. Investigate and take corrective action to elim-

inate the cause of wheel binding.

uDo not restart the cutting operation in the workpiece.

Let the wheel reach full speed and carefully re-enter

the cut. The wheel may bind, walk up or kickback if the

power tool is restarted in the workpiece.

uSupport panels or any oversized workpiece to minim-

ize the risk of wheel pinching and kickback. Large

workpieces tend to sag under their own weight. Supports

must be placed under the workpiece near the line of cut

and near the edge of the workpiece on both sides of the

wheel.

uUse extra caution when making a “pocket cut” into ex-

isting walls or other blind areas. The protruding wheel

may cut gas or water pipes, electrical wiring or objects

that can cause kickback.

uDo not attempt to do curved cutting. Overstressing the

wheel increases the loading and susceptibility to twisting

or binding of the wheel in the cut and the possibility of

kickback or wheel breakage, which can lead to serious in-

jury.

Safety warnings specific for sanding operations:

uUse proper sized sanding disc paper. Follow manufac-

turers recommendations, when selecting sanding pa-

per. Larger sanding paper extending too far beyond the

sanding pad presents a laceration hazard and may cause

snagging, tearing of the disc or kickback.

Safety warnings specific for wire brushing operations:

uBe aware that wire bristles are thrown by the brush

even during ordinary operation. Do not overstress the

wires by applying excessive load to the brush The wire

bristles can easily penetrate light clothing and/or skin.

uIf the use of a guard is specified for wire brushing, do

not allow any interference of the wire wheel or brush

with the guard. Wire wheel or brush may expand in dia-

meter due to work load and centrifugal forces.

Additional safety information

Wear safety goggles.

The protective guard must not be used for

cutting. With a suitable adapter, the protective

guard can also be used for cutting.

Hold the power tool firmly with both hands

and make sure you have a stable footing. The

power tool can be more securely guided with

both hands.

uFor application tools with an internal thread, such as

brushes and diamond annular cutters, attention must

be paid to the max. thread length of the grinding

spindle. The spindle end must not touch the base of the

application tool.

uUse suitable detectors to determine if utility lines are

hidden in the work area or call the local utility com-

pany for assistance. Contact with electric lines can lead

to fire and electric shock. Damaging a gas line can lead to

explosion. Penetrating a water line causes property dam-

age or may cause an electric shock.

uDo not touch grinding and cutting discs until they have

cooled down. The discs can become very hot while work-

ing.

uRelease the On/Off switch and set it to the off position

when the power supply is interrupted, e. g., in case of

a power failure or when the mains plug is pulled. This

prevents uncontrolled restarting.

uSecure the workpiece. A workpiece clamped with

clamping devices or in a vice is held more secure than by

hand.

uStore the application tools inside buildings, in a dry,

frost-free room at a uniform temperature.

uRemove the application tools before transporting the

power tool. This will allow you to avoid damage.

uBonded cutting and grinding discs have an expiration

date, after which the discs must no longer be used.

Products sold in GB only:

Your product is fitted with an BS 1363/A approved electric

plug with internal fuse (ASTA approved to BS 1362).

If the plug is not suitable for your socket outlets, it should be

cut off and an appropriate plug fitted in its place by an au-

thorised customer service agent. The replacement plug

should have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible

shock hazard and should never be inserted into a mains

socket elsewhere.

Product Description and

Specifications

Read all the safety and general instructions.

Failure to observe the safety and general in-

structions may result in electric shock, fire

and/or serious injury.

Please observe the illustrations at the beginning of this oper-

ating manual.

Intended use

The power tool is intended for cutting and brushing metal,

stone, plastic and composite materials, roughing metal,

plastic and composite materials as well as making holes in

stone materials using diamond annular cutters, without the

use of water. Make sure that the correct protective guard is

used(see "Operation", page30).

Bosch Power Tools 1 609 92A 6A0 | (11.02.2022)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GWS 17-150 S Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info