Bedienungsanleitung Bosch gws 23 230 js (Seite 17 von 122) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

390511

Zoom out

Zoom in

Vorherige Seite

1/122

Nächste Seite

English - 4

1 609 929 B76 • TMS • 30.11.00

■ Before any work on the machine itself, pull

the mains plug.

Use only grinding tools with a permissi-

ble speed at least as high as the no-load

speed of the machine.

Roughing and cutting discs become

very hot while working; do not touch un-

til they have cooled.

■ Clean the grinder spindle and all parts to be

mounted. For clamping and loosening the

grinding tools, lock the grinder spindle 6 with

the spindle locking button 2.

Actuate the spindle locking button 2 only

when the grinder spindle is at a standstill!

Roughing/Cutting Disk

The hole of the roughing/cutting disk must fit on

the centring shoulder of the mounting flange 9

without play. Do not use reducer pieces or adapt-

ers.

When using a diamond cutting disk, take care

that the direction of rotation arrow on the dia-

mond cutting disk and the direction of rotation of

the machine (direction of rotation arrow on the

machine head) agree.

For mounting, see the illustration page.

Screw on the clamping nut 11 and tighten with

the two-hole spanner (see Section “Quick Clamp-

ing Nut”).

An O-ring (plastic

part) is inserted in

the retainer flange 9

around the spigot.

If the O-ring is missing or is damaged, it must

in all cases be replaced (Order No.

1 600 210 039) before the retainer flange 9 is

mounted.

☞

After mounting the grinding tool and be-

fore switching on, check that the grind-

ing tool is correctly mounted and that it

can turn freely.

Flap disc

Remove the protective guard 5 and mount the

hand protector 17. Place the special retainer

flange 9 (optional extra, Order No.

2 605 703 028) and the flap disc on the grinder

spindle 6. Screw on the clamping nut 11 and

tighten with the two-hole spanner.

Rubber Sanding Plate 19

Remove the protective guard 5 and mount the

hand protector 17.

Before the rubber sanding plate 19 is mounted

first place the 2 spacers 18 onto the grinding

spindle.

For mounting, see the illustration page.

Screw on the round nut 21 and tighten with the

two-hole spanner.

Cup Brush 22/Disc brush

Remove the protective guard 5 and mount the

hand protector 17.

The grinding tool must be able to be screwed

onto the grinding spindle 6 until it rests firmly

against the grinder spindle flange at the end of

the grinder spindle threads. Tighten with an

open-ended spanner.

Grinding cup

When working with grinding cups, use a

special guard 15.

The grinding cup 16 should always protrude

from the guard 15 only as far as absolutely nec-

essary for the work to be performed in each case.

Adjust the guard 15 to this distance.

For mounting, see the illustration page.

Screw on the clamping nut 11 and tighten with a

suitable offset two-hole spanner.

Mounting the Grinding Tools

(Optional Accessories)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch gws 23 230 js Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info