Bedienungsanleitung Bosch gws 25 180 j sds (Seite 16 von 122) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

390503

Zoom out

Zoom in

Vorherige Seite

1/122

Nächste Seite

English - 3

1 609 929 B76 • TMS • 30.11.00

■ When grinding metal, flying sparks are pro-

duced. Take care that no persons are endan-

gered. Due to danger of fire, no combustible

materials should be located in the vicinity

(spark flight zone).

■ Be careful when cutting grooves, e. g. in load-

carrying walls: See information on structures.

■ Be careful of hidden electrical lines or gas and

water pipes. Check the working area, e. g. with

a metal detector.

■ Blocking the cutting disc leads to jerking reac-

tion forces on the machine. In this case switch

off the machine immediately.

■ Pay attention to the dimensions of the grinding

disc. The mounting hole diameter must fit the

mounting flange 9 without play. Do not use re-

ducer pieces or adapters.

■ Never use cutting discs for rough grinding. Do

not exert any lateral pressure on the cutting

discs.

■ Observe the manufacturer’s instructions for

mounting and using grinding tools.

■ Caution! The grinding tool runs on after the

machine is switched off.

■ Do not clamp the machine in a vice.

■ Bosch is only able to ensure perfect function-

ing of the machine if the original accessories

intended for it are used.

The machine is intended for cutting, roughing and

brushing metal and stone materials without using

water. For cutting stone, a cutting guide is re-

quired.

Slots in load carrying walls are subject to the

Standard DIN 1053, Part 1 or country-specific

regulations.

These regulations are to be observed under all

circumstances. Before beginning work, consult

the responsible structural engineer, architects or

the construction supervisor.

■ Before any work on the machine itself, pull

the mains plug.

■ For work with roughing or cutting discs,

the protective guard 5 must be mounted.

Guard with locking screw

The coded projection 14 on the guard 5 ensures

that only a guard that fits the machine type can be

mounted.

Loosen the clamping screw 13, if necessary.

Place the guard 5 with coded projection 14 into

the coded groove on the spindle collar of the ma-

chine head and rotate to the required position

(working position).

The closed side of the protective guard 5

must always point to the operator.

Tighten clamping screw 13.

Guard with quick clamp

(Optional extra)

☞

The guard is pre-adjusted to the diameter

of the spindle collar. Therefore do not

loosen or tighten the adjustment screw 7.

Open the clamping lever 8.

Place the protective guard 5 on the spindle collar

of the machine head and turn to the required po-

sition (working position).

To fasten the protective guard 5, close the clamp-

ing lever 8.

The closed side of the protective guard 5

must always point to the operator.

Auxiliary Handle

■ For all work with the machine, the auxiliary

handle 4 must be mounted.

Screw the auxiliary handle 4 into the head of the

machine according to the working method.

Hand Protector (Optional extra)

For work with the rubber sanding plate 19 or with

the cup brush 22/disc brush/flap disc, mounting

the hand protector 17 (optional extra) is recom-

mended. The hand protector 17 is fastened with

the auxiliary handle 4.

Intended Use

Information Structures

Mounting the

Protective Devices

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch gws 25 180 j sds Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info