Bedienungsanleitung Bosch gws 25 180 j sds (Seite 19 von 122) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

390503

Zoom out

Zoom in

Vorherige Seite

1/122

Nächste Seite

English - 6

1 609 929 B76 • TMS • 30.11.00

Check for correct mains voltage: The voltage

of the power source must agree with the voltage

specified on the nameplate of the machine.

Equipment marked with 230 V can also be con-

nected to 220 V.

Switching on: Slide the On/Off switch 3

forward without exerting any

pressure.

Press the On/Off switch 3.

Switching off: Release the On/Off switch 3.

Locking: Continue to slide the

On/Off switch 3 forward whilst

depressed.

Switching off: Press and release On/Off

switch 3.

Switch configuration without lock

(specific countries):

Switching on: Slide the On/Off switch 3

forward without exerting any

pressure.

Press the On/Off switch 3.

Switching off: Release the On/Off switch 3.

☞

Test run!

Check the grinding tool before use. The

grinding tool must be flawlessly mounted

and be able to rotate freely. Perform a test

run of at least 30 seconds without load. Do

not use damaged, out-of-round or vibrating

grinding tools.

Starting Current Limiting

(Type J)

As a result of soft starting, a 13-A fuse is

adequate.

A machine without starting current-limiter

requires a higher fuse protection.

■ Clamp the workpiece if it does not remain

stationary due to its own weight.

■ Do not load the machine so heavily that it

comes to a standstill.

■ Roughing and cutting discs become very

hot while working; do not touch until they

have cooled.

Rough Grinding

With an approach angle of 30° to

40°, the best roughing results can

be achieved. Move the machine

back and forth with moderate pres-

sure. In this manner, the work piece

will not become too hot, does not

discolour and no ridges are formed.

Never use a cutting disc for roughing.

Flap disc

With the flap disc (optional extra), curved sur-

faces and profiles (contour sanding) can be

worked.

Flap discs have a considerably higher service life

than sanding sheets, lower noise level and lower

sanding temperatures.

Cutting

When cutting, do not press, tilt or

oscillate. Work with moderate ad-

vancing that is adapted to the mate-

rial being worked.

Do not brake coasting cutting disks

with side pressure.

Important is the di-

rection in which cut-

ting is performed.

The machine must

always work opposite

to the direction of ro-

tation. Therefore,

never move the ma-

chine in the other di-

rection! Otherwise,

the danger exists of it

being pushed un-

controlled out of the

cut.

Cutting grinder Stand

With the cutting grinder stand (optional extra),

work pieces of the same length can be cut at an-

gles of 0 to 45°.

When cutting profiles and square pipes, it is best

to start with the smallest cross section.

For mounting the machine in the cutting stand a

cap or a claw are required, depending on the type

of cutting stand used.

Initial Operation

Operating Instructions

16 A

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch gws 25 180 j sds Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info