Bedienungsanleitung Bosch GWS 26-180 (Seite 39 von 46) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

119917

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

English

OPTIONAL ACCESSORIES (sold separately)

1. Battery (EB914, EB9B, EB9H, EB926H, EB930H)

(For DS9DVB2)

2. Battery (EB1214S, EB1214L, EB1220BL, EB1222HL,

EB1226HL, EB1230HL)

(For DS12DVB2)

3. Battery (EB1414S, EB1414, EB14B, EB1426H, EB1430H)

(For DS14DVB2)

4. Battery (EB1814SL, EB1820, EB1820L, EB1826HL,

EB1830HL)

(For DS18DVB2)

Optional accessories are subject to change without notice.

APPLICATIONS

⅜ Driving and removing of machine screws, wood

screws, tapping screws, etc.

⅜ Drilling of various metals.

⅜ Drilling of various woods.

BATTERY REMOVAL/INSTALLATION

1. Battery removal

Hold the handle tightly and push the battery latch (1

pc. or 2 pcs.) to remove the battery (See Figs. 1 and 2).

CAUTION

Never short-circuit the battery.

2. Battery installation

Insert the battery while observing its polarities (see

Fig. 2).

CHARGING

Before using the driver drill, charge the battery as follows.

〈〈

〈

UC12SD/UC14SD/UC18SD

〉〉

〉

1. Insert the battery into the charger

Insert the battery firmly while observing its direction,

until it contacts the bottom of the charger (See Fig. 3 ).

CAUTION

The UC12SD, UC14SD, and UC18SD models are the

exclusively designed chargers. These cannot charge

batteries except the specified batteries. It is possible

to insert the batteries other than the specified into

the chargers and some of them may light up the pilot

lamps. However, you are requested to exercise utmost

caution not to charge batteries other than specified

ones because these can not only be charged but also

such actions can result in the malfuntion of chargers.

2. Connect the charger power cord to the receptacle

Connecting the power cord will turn on the charger

(the pilot lamp lights up).

CAUTION

If the pilot lamp does not light up, pull out the power

cord from the AC outlet and check the battery

mounting condition.

About 60 minutes are required to fully charge the

battery at a temperature of about 20°C. The pilot

lamp goes off to indicate that the battery is fully

charged.

The battery charging time becomes longer when a

temperature is low or the voltage of the power source

is too low.

When the pilot lamp does not go off even if more

than 120 minutes have elapsed after starting of the

charging, stop the charging and contact your HITACHI

authorized service center.

CAUTION

If the battery is heated due to direct sunlight, etc., just

after operation, the charger pilot lamp may not light

up. At that time, cool the battery first, then start

charging.

3. Disconnect the charger’s power cord from the

receptacle

4. Hold the charger firmly and pull out the battery

NOTE

After operation, pull out batteries from the charger

first, and then keep the batteries properly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GWS 26-180 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch GWS 26-180

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info