Bedienungsanleitung Bosch GWS 26-180 (Seite 21 von 261) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

119917

Zoom out

Zoom in

Vorherige Seite

1/261

Nächste Seite

English - 8

■ Before any work on the machine itself, pull

the mains plug.

The machine head

can be rotated with

respect to the ma-

chine housing in 90°

steps. In this man-

ner, the On/Off

switch can be

brought to an advan-

tageous handling

position for special

working situations,

e. g., for cutting work

with the cutting guide 25/cutting grinder stand 28

(accessory) or for left-handed persons.

Unscrew completely the four screws.

Rotate the machine head carefully and without

removing from the housing to the new position.

Screw in the screws again and tighten.

The handle 27 can be turned with respect to the

motor housing by 90° either to the left or right.

This allows for the On/Off switch to be positioned

more conveniently for certain working situations,

e. g., for cutting work with the cutting guide/

grinder stand (accessories) and for left-handers.

Pull the handle unlocking button 26 firmly in the

direction of the arrow (

➊), turning the handle 27

at the same time to the desired position (

➋) until

it engages. The figure shows the handle 27

turned by 90°.

☞

The handle unlocking button 26 and the

On/Off switch 3 have a safety interlock.

The machine cannot be switched on if the

handle 27 is not engaged in one of the

three possible positions.

The handle 27 cannot be unlocked if the

On/Off switch 3 is locked.

■ Before any work on the machine itself, pull

the mains plug.

☞

For safe and proper working, always keep

the machine and the ventilation slots clean.

In extreme working conditions, conductive

dust can accumulate in the interior of the

machine when working with metal. The

protective insulation of the machine can be

degraded. The use of a stationary extrac-

tion system is recommended in such cases

as well as frequently blowing out the venti-

lation slots and installing a residual current

device (RCD).

If the machine should fail despite the care taken

in manufacturing and testing procedures, repair

should be carried out by an after-sales service

centre for Bosch power tools.

In all correspondence and spare parts orders,

please always include the 10-digit order number

given on the nameplate of the machine.

WARNING! Important instructions for con-

necting a new 3-pin plug to the 2-wire cable.

The wires in the cable are coloured according to

the following code:

Do not

connect the blue or brown wire to the

earth terminal of the plug.

Important: If for any reason the moulded plug is

removed from the cable of this machine, it must

be disposed of safely.

Rotating the Machine Head

Turning the Machine Handle

(GWS 24/26-180/230 (J)B)

➊

➋

Maintenance and Cleaning

strain relief

live = brown

neutral = blue

To be fitted

by qualified

professional only

1 609 929 R35.book Seite 8 Mittwoch, 13. Februar 2008 1:16 13

22 • 1 609 929 R35 • 03.11

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GWS 26-180 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch GWS 26-180

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info