Bedienungsanleitung Bosch gws 9 125 c (Seite 15 von 107) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

390514

Zoom out

Zoom in

Vorherige Seite

1/107

Nächste Seite

EURO • Printed in Germany • BA 1 609 929 C85 • GWS 7-14-1000 • OSW 12/01

English - 3

■ Always switch the machine off and wait until it

has come to a standstill before placing it down.

■ Insert the mains plug only when the machine is

switched off.

■ For mains failure or when the main plug is

pulled, unlock the On/Off switch immediately

and turn it to the off position. This prevents un-

controlled restarting.

■ The machine must be used only for dry cutting/

grinding.

■ For all work with the machine, the auxiliary

handle 3 must be mounted.

■ Hold the power tool only by the insulated

gripping surfaces, when performing an op-

eration where the cutting tool may run into

hidden wiring or its own cord.

Contact with a “live” wire will make exposed

metal parts of the tool “live” and shock the op-

erator.

■ Do not drill, cut or saw into blind areas

where electric, gas or water lines may exist.

Use suitable detectors to determine if these

lines are hidden in the work area or call the

local utility company for assistance.

Contact with electric lines may cause fire or

electric shock. Damaging a gas line can result

in an explosion. Penetrating a water pipe will

cause property damage or may cause an elec-

tric shock.

■ For work with roughing or cutting discs, the

protective guard 6 must be mounted. For work

with the rubber sanding plate 13 or with the

cup brush 16/disc brush/flap disc, mounting

the hand protector 12 (accessory) is recom-

mended.

■ Use a vacuum cleaner for drawing off the dust

when working with stone. The vacuum cleaner

must be approved for masonry dust. When

cutting stone, use the cutting guide.

■ Do not work with materials containing asbes-

tos.

■ Use only grinding tools with a permissible

speed at least as high as the no-load speed of

the machine.

■ Check grinding tools before use. The grinding

tool must be properly mounted and turn freely.

Perform a test run for at least 30 seconds with-

out load. Do not use damaged, out-of-round or

vibrating grinding tools.

■ Protect the grinding tool from impact, shock

and grease.

■ Apply the machine to the workpiece only when

switched on.

■ Keep hands away from rotating grinding tools.

■ Pay attention to the direction of rotation. Al-

ways hold the machine so that sparks and

grinding dust fly away from the body.

■ When grinding metal, flying sparks are pro-

duced. Take care that no persons are endan-

gered. Due to danger of fire, no combustible

materials should be located in the vicinity

(spark flight zone).

■ Be careful when cutting grooves, e. g. in load-

carrying walls: See information on structures.

■ Blocking the cutting disc leads to jerking reac-

tion forces on the machine. In this case switch

off the machine immediately.

■ Pay attention to the dimensions of the grinding

disc. The mounting hole diameter must fit the

mounting flange 8 without play. Do not use re-

ducer pieces or adapters.

■ Never use cutting discs for rough grinding. Do

not exert any lateral pressure on the cutting

discs.

■ Observe the manufacturer’s instructions for

mounting and using grinding tools.

■ Caution! The grinding tool runs on after the

machine is switched off.

■ Do not clamp the machine in a vice.

■ Never allow children to use the machine.

■ Bosch is only able to ensure perfect operation

of the machine if the original accessories in-

tended for it are used.

Slots in load carrying walls are subject to the

Standard DIN 1053, Part 1 or country-specific

regulations.

These regulations are to be observed under all

circumstances. Before beginning work, consult

the responsible structural engineer, architects or

the construction supervisor.

Information Structures

GWS 7-14-1000 - Buch Seite 3 Montag, 3. Dezember 2001 10:49 10

16 • 1 609 929 C85 • TMS • 26.11.01

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch gws 9 125 c Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info