Bedienungsanleitung Bosch GWX 13-125 S (Seite 23 von 347) (Alle Sprachen)

786310

Zoom out

Zoom in

Vorherige Seite

1/347

Nächste Seite

English | 23

uProvide sufficient dust extraction when cutting stone.

The protective guard for cutting (9) is fitted in the same way

as the protective guard for grinding (7).

Extraction guard for cutting with a guide block

The extraction guard for cutting with a guide block (18) is fit-

ted in the same way as the protective guard for grinding (7).

Side handle

uDo not operate your power tool without the side

handle (6).

uDo not continue to use the power tool if the auxiliary

handle is damaged. Do not make any alterations to the

auxiliary handle.

Screw the side handle (6) on the left or right of the machine

head depending on how your are working.

Low-vibration auxiliary handle

The low-vibration auxiliary

handle reduces vibration,

enabling the tool to be used

safely and more comfort-

ably.

uDo not make any alterations of any kind to the auxili-

ary handle.

Do not continue to use a damaged auxiliary handle.

Hand guard

uAlways fit the hand guard (14) when working with the

cup brush/disc brush (15) or diamond core cutter (20).

Attach the hand guard (14) to the auxiliary handle (6).

Fitting and removing abrasive tools

Follow the special assembly instructions for

X-LOCK application tools.

uPull the plug out of the socket before carrying out any

work on the power tool.

uDo not touch grinding and cutting discs until they have

cooled down. The discs can become very hot while work-

ing.

uOnly use original X-LOCK application tools that carry the

X-LOCK logo. A maintained clamping gauge of max.

1.6mm can only be guaranteed with original X-LOCK ap-

plication tools. A higher clamping gauge can lead to insec-

ure clamping, potentially causing the clamp tool to come

loose.

uX-LOCK application tools do not need additional clamping

flanges or support flanges.

uMake sure that the application tool and the holder are not

deformed and are free from dirt and particles.

Pay attention to the dimensions of the abrasive tools.

Make sure that both X-LOCK catches are open (see figure

below) before fitting the X-LOCK application tool.

If necessary, clean the area between the two X-LOCK

catches.

Fitting the abrasive tool

Place the grinding/cutting/flap disc in a central position

on the X-LOCK holder, parallel to the bearing surface

and with the right side facing up.

Push the disc into the holder.

The disc audibly clicks into place. Do not actuate the

lever (3) when doing so.

(3)

uAfter fitting, check that the edge of the abrasive tool

() is fitted correctly, i.e. is no higher than the refer-

ence surface (). If the edge is higher than the refer-

ence surface, either the holder must be cleaned or the

abrasive tool must not be used.

Before removing the grinding/cutting/flap disc: Make

sure that the power tool has come to a complete stop.

Removing the abrasive tool

Open the lever (3).

The grinding/cutting/flap disc will be released.

The grinding/cutting/flap disc can be removed.

(3) (3)

Cup brushes/disc brushes and fibre discs

uAlways fit the hand guard (14) when working with the

cup brush/disc brush or fibre disc.

Bosch Power Tools 1 609 92A 7VN | (31.05.2022)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GWX 13-125 S Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info