Bedienungsanleitung Bosch GWX 14-125 (Seite 26 von 347) (Alle Sprachen)

786305

Zoom out

Zoom in

Vorherige Seite

1/347

Nächste Seite

26 | English

and an increased risk of losing control of the power

tool, which can lead to kickback.

For cutting stone, it is best to use a diamond cutting disc.

When using the extraction guard for cutting with a cutting

guide(23), the dust extractor must be approved for extract-

ing stone dust. Suitable dust extractors are available from

Bosch.

Switch on the power tool

and position it with the

front part of the cutting

guide on the workpiece.

Move the power tool with a

moderate feed motion that

is suited to the material be-

ing machined.

When cutting especially

hard materials such as con-

crete with a high pebble content, the diamond cutting disc

can overheat and become damaged as a result. This is

clearly indicated by circular sparking, rotating with the dia-

mond cutting disc.

If this happens, stop cutting and allow the diamond cutting

disc to cool down by running the power tool for a short time

at maximum speed with no load.

If work is noticeably slower and with circular sparking, this

indicates that the diamond cutting disc has become blunt.

You can resharpen the disc by briefly cutting into abrasive

material (e.g. lime-sand brick).

Cutting other materials

uFor cutting materials such as plastic, composite ma-

terials, etc. with bonded cutting discs or Carbide Multi

Wheel cutting discs, always use the protective guard

for cutting(8) or the protective guard for grinding(7)

with a fitted cover for cutting (11). You can achieve

improved dust extraction by using the extraction

guard with a cutting guide(23).

Working with Diamond Annular Cutters

uOnly use dry diamond annular cutters.

uAlways fit the hand guard (16) when working with dia-

mond annular cutters.

Do not place the diamond annular cutter parallel to the work-

piece. Plunge it into the workpiece at an angle and in a circu-

lar motion. This will allow you to achieve optimal cooling and

ensure a longer tool life for the diamond annular cutter.

Information on structural design

Recesses in load-bearing walls are subject to country-spe-

cific regulations. These regulations must be observed under

all circumstances. Seek advice from the responsible struc-

tural engineer, architect or construction supervisor before

starting work.

Start-up

When operating the power tool using a mobile generator that

does not have sufficient reserve capacity or an adequate

voltage control system with inrush current boost converter,

loss of performance or atypical behaviour may occur upon

switch-on.

Please check the suitability of the power generator you are

using, particularly with regard to the mains voltage and fre-

quency.

uProducts that are only sold in AUS and NZ: Use a resid-

ual current device (RCD) with a nominal residual current

of 30 mA or less.

uPay attention to the mains voltage. The voltage of the

power source must match the voltage specified on the

rating plate of the power tool.

Switching on/off

To start the power tool, push the on/off switch (4) forward.

To lock the on/off switch (4) in position, push the on/off

switch (4) forward and down until it clicks into place.

To switch off the power tool, release the on/off switch (4);

or, if the switch is locked, briefly push the on/off switch (4)

backward and down and then release it.

uAlways check abrasive tools before using them. The

abrasive tool must be fitted properly and be able to

move freely. Carry out a test run for at least one

minute with no load. Do not use abrasive tools that are

damaged, run untrue or vibrate during use. Damaged

abrasive tools can burst apart and cause injuries.

Maintenance and Service

Maintenance and Cleaning

uPull the plug out of the socket before carrying out any

work on the power tool.

uTo ensure safe and efficient operation, always keep

the power tool and the ventilation slots clean.

uIn extreme conditions, always use a dust extractor if

possible. Blow out ventilation slots frequently and in-

stall a residual current device (RCD) upstream. When

machining metals, conductive dust can settle inside the

power tool, which can affect its protective insulation.

Store and handle the accessories carefully.

In order to avoid safety hazards, if the power supply cord

needs to be replaced, this must be done by Bosch or by an

after-sales service centre that is authorised to repair Bosch

power tools.

After-Sales Service and Application Service

Our after-sales service responds to your questions concern-

ing maintenance and repair of your product as well as spare

parts. You can find explosion drawings and information on

spare parts at: www.bosch-pt.com

The Bosch product use advice team will be happy to help you

with any questions about our products and their accessor-

ies.

In all correspondence and spare parts orders, please always

include the 10‑digit article number given on the nameplate

of the product.

1 609 92A 765 | (17.03.2022) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GWX 14-125 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info