Bedienungsanleitung Bosch GWX 18V-8 (Seite 22 von 383) (Alle Sprachen)

786204

Zoom out

Zoom in

Vorherige Seite

1/383

Nächste Seite

22 | English

uDo not attempt to do curved cutting. Overstressing the

wheel increases the loading and susceptibility to twisting

or binding of the wheel in the cut and the possibility of

kickback or wheel breakage, which can lead to serious in-

jury.

Safety warnings specific for sanding operations:

uUse proper sized sanding disc paper. Follow manufac-

turers recommendations, when selecting sanding pa-

per. Larger sanding paper extending too far beyond the

sanding pad presents a laceration hazard and may cause

snagging, tearing of the disc or kickback.

Safety warnings specific for wire brushing operations:

uBe aware that wire bristles are thrown by the brush

even during ordinary operation. Do not overstress the

wires by applying excessive load to the brush The wire

bristles can easily penetrate light clothing and/or skin.

uIf the use of a guard is specified for wire brushing, do

not allow any interference of the wire wheel or brush

with the guard. Wire wheel or brush may expand in dia-

meter due to work load and centrifugal forces.

Additional safety information

Wear safety goggles.

The protective guard must not be used for

cutting. With a suitable adapter, the protective

guard can also be used for cutting.

Hold the power tool firmly with both hands

and make sure you have a stable footing. The

power tool can be more securely guided with

both hands.

uUse suitable detectors to determine if there are hid-

den supply lines or contact the local utility company

for assistance. Contact with electric cables can cause

fire and electric shock. Damaging gas lines can lead to ex-

plosion. Breaking water pipes causes property damage.

uDo not touch grinding and cutting discs until they have

cooled down. The discs can become very hot while work-

ing.

uRelease the On/Off switch and set it to the Off posi-

tion when the power supply is interrupted, e.g. when

the battery pack is removed. This prevents uncontrolled

restarting.

uSecure the workpiece. A workpiece clamped with

clamping devices or in a vice is held more secure than by

hand.

uStore the application tools inside buildings, in a dry,

frost-free room at a uniform temperature.

uRemove the application tools before transporting the

power tool. This will allow you to avoid damage.

uBonded cutting and grinding discs have an expiration

date, after which the discs must no longer be used.

uIn case of damage and improper use of the battery, va-

pours may be emitted. The battery can set alight or ex-

plode. Ensure the area is well ventilated and seek medical

attention should you experience any adverse effects. The

vapours may irritate the respiratory system.

uDo not open the battery. There is a risk of short-circuit-

ing.

uThe battery can be damaged by pointed objects such

as nails or screwdrivers or by force applied externally.

An internal short circuit may occur, causing the battery to

burn, smoke, explode or overheat.

uOnly use the battery with products from the manufac-

turer. This is the only way in which you can protect the

battery against dangerous overload.

Protect the battery against heat, e.g. against

continuous intense sunlight, fire, dirt, water

and moisture. There is a risk of explosion and

short-circuiting.

Product Description and

Specifications

Read all the safety and general instructions.

Failure to observe the safety and general in-

structions may result in electric shock, fire

and/or serious injury.

Please observe the illustrations at the beginning of this oper-

ating manual.

Intended use

The power tool is intended for cutting and brushing metal,

stone, plastic and composite materials, roughing metal,

plastic and composite materials as well as making holes in

stone materials using diamond annular cutters, without the

use of water. Make sure that the correct protective guard is

used(see "Operation", page27).

Sufficient dust extraction must be provided when cutting

stone.

With approved abrasive tools, the power tool can be used for

sanding with sanding discs.

The power tool must not be used to grind stone materials

with diamond grinding heads.

Product features

The numbering of the product features refers to the diagram

of the power tool on the graphics page.

(1) Unlocking lever for protective guard

(2) Direction of rotation arrow on housing

(3) Lever

(4) LED work light

(5) On/off switch

(6) Rechargeable batterya)

(7) Rechargeable battery release buttona)

1 609 92A 76B | (16.02.2022) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GWX 18V-8 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info