Bedienungsanleitung Bosch Indego S 500 (Seite 32 von 356) (Alle Sprachen)

764284

Zoom out

Zoom in

Vorherige Seite

1/356

Nächste Seite

32 | English

Problem Possible Cause Corrective Measure

Mower standing on

lawn with the display

switched off

Operational problems Press confirm button for screen to light up, or place

mower in docking station.

Mower does not

charge Battery too hot/cold The mower operates when the battery internal temperat-

ure is between 5°C – 45°C. Allow mower to cool down/

warm up. If the error occurs frequently, the docking sta-

tion should be positioned in the shade.

Docking station not switched on Switch on power supply to docking station. If docking

station does not start, contact your Bosch Service

Centre.

Charging pins corroded Clean the charging pins.

Battery not fitted, incorrectly fitted or in-

correct battery for mower Insert battery correctly (see figure L). Use the appropri-

ate Bosch battery.

Mower out of peri-

meter wire Perimeter wire on a slope Leave 30 cm between the perimeter wire and the slope.

Obstacle near perimeter wire Remove obstacle.

Parts of the lawn area

left uncut Mower requires more cuts to finish garden Allow mower to run for 3 full cuts to cover whole lawn

area. Alternatively use the "Intensive mode" under "Mow-

ing mode".

Time slot not long enough for garden size Increase mowing time slot or:

– use “Bosch AUTO” calendar function (with Indego

S500 and M700)

– use Bosch “SmartMowing” functionality (with In-

dego S+500 and M+700)

Distance between perimeter wires too

small Increase distance between the perimeter wires to a min-

imum of 75 cm.

Rough mowing conditions Select "uneven ground/low sensitivity" option from menu

item "lawn condition/bump sensor".

Flatten garden/remove/bumps/mark out unsuitable

areas with the perimeter wire – Please follow the instruc-

tions in the Installation Guide.

Grass too long Select "uneven ground/low sensitivity" option from menu

item "lawn condition/bump sensor".

Slopes in garden too steep Ensure mower only operates on slopes of 15 degrees or

less and full garden is not on a slope.

Mower gets stuck in

garden Objects/obstacles not marked out Use the perimeter wire to mark off obstacles where the

mower often gets stuck.

Newly laid turf Allow a few weeks for the soil to settle before using the

mower.

Change setting in menu item "lawn condition / bump

sensor" to low sensitivity / uneven.

After watering, wait as long as possible until you start the

mower.

Mower unintentionally

cuts flowers, etc. or

runs over certain

obstacles

Objects/obstacles below 5cm not marked

out Mark obstacle using perimeter wire leaving 30cm from

object or remove objects/obstacles.

Mower does not ap-

pear to cut logically LogiCut system depends on the garden

conditions. Mower does not necessarily

have to continue in the next uncut area.

Further information can be found on the Installation

Guide.

If behaviour re-occurs often, remap garden.

F 016 L94 038 | (11.11.2020) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch Indego S 500 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info